Jump to content
SAU Community

Recommended Posts

Just had compression test done

Results came back rubbish

Between 111-114 across all six.

Mechanic said he is going to use another dial just to be certain, as the wear is very even.

f**king disappointing,

Question :

Wouldnt rubbish figures like that be showing serious deteriorating performance signs??? I had this done out of curiosity as i was just about to upgrade turbo. Still performs like it always has. Really well. Has a 125k on the clock

Link to comment
https://www.sau.com.au/forums/topic/360991-compression-results/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

1. They are consistent - this is good, not rubbish

2. It could have been done slightly wrong - meaning there is no actual issue

Given consistent results across all 6 it's either one of two things.

The motor is a little bit tired or the test was perhaps not dont quite correctly.

Have it retested perhaps by another workshop just to see what happens. With legit km's you'd probably expect closer to 130-140 but personally i wouldnt get too excited just yet until it gets retested.

If it comes back and does show that it is similarly low then ye the motor is a bit tired and perhaps not a good idea to ask too much of it. 250rwkw on a safe tune would be about sensible limit IMO.

1. They are consistent - this is good, not rubbish

2. It could have been done slightly wrong - meaning there is no actual issue

Given consistent results across all 6 it's either one of two things.

The motor is a little bit tired or the test was perhaps not dont quite correctly.

Have it retested perhaps by another workshop just to see what happens. With legit km's you'd probably expect closer to 130-140 but personally i wouldnt get too excited just yet until it gets retested.

If it comes back and does show that it is similarly low then ye the motor is a bit tired and perhaps not a good idea to ask too much of it. 250rwkw on a safe tune would be about sensible limit IMO.

Good to hear i guess.

Was only aiming for 250rwkw give or take and decent response.

Its being retested with another dial. If its still the same, taking it elsewhere for one last crack regardless.

Cheers for your response.

I get it changed every 5 thousand. Its not burning oil or blowing excessive smoke. Doesnt go through coolant either

Does however not seem to peak as much boost. Originally tuned for around 13psi. Now under load (and even on the cooler nights recently) only seems to reach just on 11psi.

Occasionally the idle drops off slightly from around 700 to 500 revs and has stalled once or twice coming to a real quick stop at the lights.

Ive never had the 02 replaced.

Edited by Mattw_83

I wouldnt worry about it it to much considering the numbers are very very even, as someone else said, put a couple drops of oil in through the plug hole and do the test again and also do a leak down test and it'll tell the story a bit better, i'd say its just old age and or probaly had a headgasket changed to a thicker item before you bought the car

Slap your new turbo on and screw the boost into is what i'd be doing.

Big thing i find with comp test results is from gauge to gauge it varys but as long as the numbers are with in 5% of each other she's still good!

Edited by 32rrr

The engine sounds like its a little tired. Is the motor breathing @ all, check your intercooler piping for oil if you still run a standard breather setup.

Apologies for the ignorance mate, what do you mean by breathing?

Start car, better with a mate, so he can blip the throttle.

Take your oil filler cap off and see if it is breathing heaps = indicates blowby = rings/liners worn. Keep a rag handy,so you can half cover the hole just in case it starts to spit oil.

Do it with a couple of cars if you can so you can see the difference.

Start car, better with a mate, so he can blip the throttle.

Take your oil filler cap off and see if it is breathing heaps = indicates blowby = rings/liners worn. Keep a rag handy,so you can half cover the hole just in case it starts to spit oil.

Do it with a couple of cars if you can so you can see the difference.

you can blip the throttle by pulling the cable with your hand lol....last time I took the filler cap off and did it, the cams flicked oil all over my face bahahaha

Just had compression test done

Results came back rubbish

Between 111-114 across all six.

Mechanic said he is going to use another dial just to be certain, as the wear is very even.

f**king disappointing,

Question :

Wouldnt rubbish figures like that be showing serious deteriorating performance signs??? I had this done out of curiosity as i was just about to upgrade turbo. Still performs like it always has. Really well. Has a 125k on the clock

hey mate,

for your interest i just did an engine swap but tested my rb20 (cold test) which has 339000km on it, i got between 120-127 on mine

mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...