Jump to content
SAU Community

Blitz Ecu - Rb20Det / R32

Dr Tuning
 Share

Recommended Posts

Dr Tuning Collaborator

Dr Tuning

Posted
Posted

Hey all, i have a spare Blitz ECU to suit a Manual trans up for grabs.!! I was keeping it as a spare for my 32 but have decided to sell it due to purchasing a Power FC so grab a bargain as these things are getting hard to find.!!!!

I put one of these in my S13 with the RB & it made a hell of a difference.! Eliminates the speed cut, boost cut, rev limit is higher & heaps more!! They're good if you've got all the usual mods such as a FMIC, Exhaust, Bigger turbo, Pump, Bla Bla Bla...

There usually selling anything from $250 up at the moment & there alot better than the Mines ECU's as well... I've had both & even a JUN one as well & the Mines is by far the best!!!

Gime $200 & you can take it.! Steal at this price, am after a quick sale as i need the money & its got all the seals & such, untouch... Like new!! So no offers!!

Pickup is from Sevenhills, NSW or can post at buyers expense!!

Msg me here or shoot me a PM... Cheers guys, bargain!!!

Matt

Link to comment
https://www.sau.com.au/forums/topic/361161-blitz-ecu-rb20det-r32/
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...