Jump to content
SAU Community

Buddyclub P1 Qf's 18X10 +12

heslo
 Share

Recommended Posts

heslo Grand Master

heslo

Posted
Posted

Up for sale is a set of 4 Buddyclub P1 QF's, in 18x10 with a +12 offset. Currently fitted with Federal RS-R rubber in 265/35 with about 80% tread. Coming off of my 33 GTR these are excellent rims, lightweight, look good and great fitment. Only looking to sell due to the car being off the road now for a while and looking for a change. Some gutter rash on the rims but overall good condition, willing to either sell with or without tires, not fussed either way. Pics are below, have only pictured the fronts, as they are already off the car, rears are identical tread wise, etc. Prices are negotiable, either contact via PM or SMS on 0431596795

With tires $3000

Without $2600

post-21349-0-88379800-1303022100_thumb.jpg

post-21349-0-75175200-1303022024_thumb.jpg

Cheers

Link to comment
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      AC Compressor

      By GTSBoy · Posted

      You don't need an AC mechanic to fit it. You do need one to vac the system down and fill it. That's how you get refrigerant.
    • GTSBoy
      Anti Squat Kit

      By GTSBoy · Posted

      Well, it's actually probably worse than you think. I think you have to (minimally) install GKTech's spherical bush replacements to the lower arm's inner ends, because you absolutely cannot subject the original (or poly) bushes to that much misalignment. The better option being to replace the whole lower arm with GKTech's unit. This brings sphericals to the lower inners either way you do it. And are you aware that the kit is weld in and you have to take the subframe out of the car to get it fitted? It's a fair bit of work. These issues both drive my ongoing dithering about doing this to my car, for the last couple of years.
    • kevboost7
      AC Compressor

      By kevboost7 · Posted

      The website said you need a AC technican to swap it in. Is that true? How did you fill the refridgerant? Was it easy to install?  If i just got the bracket and the new smaller AC compressor, would the other components be compatible with R134?
    • ianp
      Anti Squat Kit

      By ianp · Posted

      Hi All Finally getting back to work on the R32 this weekend and had a quick question about the GKTech anti squat kit (https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=39&_fid=eb6b5077e&_ss=c) So, this straightens out the rear LCA and increases the roll centre by 20MM which is great BUT I also have MFR roll centre adjusters (https://www.rhdjapan.com/moonface-super-lap-rc-joint-roll-center-adjuster-bnr32-ps13-rps13.html) which gives a +15MM lift. My question is whether they can/should be used together or if its going to massively effect the geometry? In my mind, I can't see that they work together but was hoping for some feedback on someone who has done this before deciding which to use or if both?   Thanks
    • TurboTapin
      Rb25 into r31/wont idle

      By TurboTapin · Posted

      Agreed. Thing has to be running absolutely pig rich as well. I would worry a lot less about your idle and start going through all your electrical before the car burns down. 
×
×
  • Create New...