Jump to content
SAU Community

Recommended Posts

Okay this is pretty much a cut and paste from the news articles but it is pretty important to us. Personally, I think speed cameras that do not reduce the road toll and do nothing but make money need to go. If you must keep them keep them in blackspot areas with significant signage to actually save peoples lives. The bullshit revenue raising that goes on especially in Sydney with the mass introduction of so called "safety cameras" has to come to an end.

The website for input is here: http://www.audit.nsw.gov.au/

and here is the specific speed camera feedback link: https://www.surveymonkey.com/s/BHMVMP8

The NSW Auditor-General has called for motorists' input into his state-wide investigation of speed cameras.

NSW motorists have been asked to nominate speed cameras they believe are being used as cash cows as part of a state-wide audit.

Auditor-General Peter Achterstraat on Tuesday called on motorists to log onto the NSW Audit Office website and have their say about the state's speed cameras, long thought to be used for revenue raising.

Earlier this month, Premier Barry O'Farrell made good on an election promise to carry out the audit, saying he would rip out any camera found to have no impact on road safety or those being used to gouge motorists.

Mr Achterstraat said he wanted feedback on each of the 172 fixed cameras, adding a large number of people thought the cameras were simply "money-making machines".

"I'll be looking at the facts and figures behind the 172 fixed speed cameras but in addition to that I want to dig a lot deeper in relation to the most controversial cameras," he told reporters.

"That's why I'm asking the public to nominate which ones of the speed cameras they think I should look at more closely.

"A large number of people are very concerned about speed cameras, and they are concerned that they are just money-making machines, but there are also a large number of people who highly value particular speed cameras and see them as very effective in having reduced traffic accidents."

The audit will also investigate the six mobile and 60 safety or red light cameras used across NSW, with a report due in July.

NSW Roads Minister Duncan Gay said the audit would help reassure motorists that cameras are being used to improve road safety, and not raise money for government.

"Motorists have genuine concerns that speed cameras have become cash cows under (the former Labor government)," Mr Gay said in a statement.

http://www.abc.net.au/news/stories/2011/04/19/3195638.htm

http://www.drive.com.au/Editorial/ArticleDetail.aspx?ArticleID=70945&vf=26

I only know Sydney metro and south coast really, so I picked

Beauty Point - Spit road

Burwood

Burwood heights

Darlinghurst

Lane Cove Tunnel

M2 Tunnel

Moore Park - Cleveland Street (MASSIVE REVENUE RAISER)

Randwick - Avoca Street

Ryde - Blaxland

Sydney - Sydney Harbour Tunnel

The Spit - Spit road

Woolloomooloo/East Sydney

Berry - Princes Highway

Nowra - Princes Highway

Wollongong - Princes Highway

The new east link in melbourne every toll point has a camera and its point to point not at that spot.

They are toll cameras! Not speed cameras (Point to point)... But they do have fixed cameras under some bridges and in the tunnel... These cameras under the bridges, specially wellington road one, have been on tv a couple times for reading hot, and about a couple weeks ago when i passed there was a blank spot in one of the lanes, one of the cameras was missing, maybe it was the so claimed dodgy one... pinch.gif

Moore Park - cleveland St. Girlfriend got done there for 60kph in a 50kph zone on a Saturday. Why is that a 50kph zone out of school hours?

I did the exactly same - camera got me at 60. Its retarded having main roads like Cleveland Street only 50kph.

most speed cameras, f**k them off - signed; the general motoring public

maybe just around blackspots or variable cameras at school zones, lower speed limit only activated when the school zone lights are flashing

There are safety cameras set up along the great western highway in st marys western sydney (where the old couple got cleaned up by the racing commodores a few years back) which is 3 lanes on either side

there is only one camera post with 2 cameras on it.

I was speaking with one of my clients who worked in the rta planning department (or something like that) who said the cameras can monitor all the lanes specifically ie; someone speeding in one lane can't be mistaken with a car travelling the speed limit next to it,

but I always see people speeding along the rightmost lane when they are being covered by a car in the middle lane.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 馃槂
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
  • Create New...