Jump to content
SAU Community

Tuning Around Stock Gtr Afms/injector Limits

NSNPWR

By NSNPWR,
in Engines & Forced Induction

 Share

Recommended Posts

NSNPWR Rising Star

NSNPWR

Posted
Posted

Firstly, I know there has been discussion about this in the past and ive read a number of threads but seeking input and opinions from those that have done it or seen it first hand coz im sitting on the fence here...

Heres the basics of my situation -

Cars a 32 GTR, before I bought it, made 270rwkw on 1 bar with -7s, PFC, Forged motor, Tomei Fuel pump, stock Injectors/AFMs and an SX Pressure Reg.

Ive since added some small Tomei cams and am now ready for a tune and somewhere around 18psi.

I bought some Siemens 740cc Injectors ages ago (can sell easy enough) but am wondering whether is it really worth doing Injectors and Z32 AFMs with these turbos?

Is is realistic and more importantly safe enough to squeeze the stock injectors and AFMs to the limits of the -7s? My tuner mentioned he can 'tune around' the stock AFMs to an extent...

I figure with the cams and 18psi it MIGHT make 300rwkw ish?

What would you do?...Im at a point where im trying not to spend on it so if I can retain stock AFMs and Injectors with the SX reg and make close enough to 300rwkw i'd prefer to!

Thoughts?

Cheers.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I made 340rwkw with stock injectors/AFMs

Obviously there was a fair bit more rail pressure, and tuned well past the AFM's limits...

The car came like that, so for safetys sake i put in 700's

300 wont be a problem though. One thing would be get the injectors flow tested/cleaned before doing it.

SECURITY Grand Master

SECURITY

Posted
Posted

i think it comes down to how reliable you want your car. if your tuner can tune around the AFM's thats fine - lots do. but on stock injectors you'd be running close to, if not on 100% duty cycle. you would be leaving a very small margin of error so things are more likely to go wrong.

personally, 85-90% duty cycle is the most i'd go at peak boost/power. you'd be well over that, most of your usable power will be in the 90-100% duty cycle range.

MrStabby Grand Master

MrStabby

Posted
Posted

IMO you could make a little more than 270 with that combo as is. First thing to check is the exhaust.

AFMs you can tune past with an element of risk, injectors are risky near 100% and fatal over 100%.

Also clean injectors flow far more than dirty ones. There was a recent thread showing injector that were flowing evenly, but flowed 20% more after they were cleaned. So, as well as rail pressure and AFR, injector cleanliness will determine how far you can get on the stockers. If they're leaking already its a no-brainer - replace them.

NSNPWR Rising Star

NSNPWR

Posted
  • Author
Posted (edited)

Cool, so you kept stocko AFMs @340rwkw Nismoid?

And MrStab, what Injectors/AFMs are you using to make 305rwkw? Stockers?

The existing Injectors arent leaking and im pretty sure theres a receipt in the pile that came with the car for having them cleaned/flowed but would do again to be safe...

But based on above, I think i'll whack the 740s I have in there and work with the stock AFMs...seems theyre 'less' of a safety issue than the injectors, as long as tuner is capable enough of working around them.

Cheers.

Edited by NSNPWR
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Cool, so you kept stocko AFMs @340rwkw Nismoid?

And MrStab, what Injectors/AFMs are you using to make 305rwkw? Stockers?

The existing Injectors arent leaking and im pretty sure theres a receipt in the pile that came with the car for having them cleaned/flowed but would do again to be safe...

But based on above, I think i'll whack the 740s I have in there and work with the stock AFMs...seems theyre 'less' of a safety issue than the injectors, as long as tuner is capable enough of working around them.

Cheers.

Yes they were stock.

I did put Nismos/injectors in after i purchased it.

Car ran fine like that for 2 years however under previous owner.

MrStabby Grand Master

MrStabby

Posted
Posted

And MrStab, what Injectors/AFMs are you using to make 305rwkw? Stockers?

Injectors are seimens 550's, but they were originally bought to replace leaking stockers before i got the -7s. AFMs are stock, so I assume they're out of resolution at full torque. In this case the tune should be extra rich in the map areas where AFMs are maxed so the engine wont lean out on a cold day (cold air = more air mass, which means it also needs more fuel, but the ECU has no way of knowing that). When the AFMs are maxed the ECU is just estimating fuel delivery based on RPM. I'm probably going to get nismo AFMs before i push it to 320-330.

NSNPWR Rising Star

NSNPWR

Posted
  • Author
Posted (edited)

The tuner should be allowing for and checking this on the dyno then, yeah?

You think the -7s will go 320-330? You mentioned exhaust, im running ceramic coated HKS split dumps into an unknown brand front pipe, into a big metal cat into a 3" pipe with one muffler right up the back...again, for the outlay, is a 3.5 worth the $$$? A few years ago ive had not been worried and just spent the $$$ but Mortgages etc change priorities!...

Edited by NSNPWR
MrStabby Grand Master

MrStabby

Posted
Posted

The tuner should be allowing for and checking this on the dyno then, yeah?

Yeah, but it cant hurt to specifically ask him to do it.

You think the -7s will go 320-330? You mentioned exhaust, im running ceramic coated HKS split dumps into an unknown brand front pipe, into a big metal cat into a 3" pipe with one muffler right up the back...again, for the outlay, is a 3.5 worth the $$$? A few years ago ive had not been worried and just spent the $$$ but Mortgages etc change priorities!...

I think 330 is possible given the current power and boost level, but I wont know until I try. I probably need a stronger clutch, and if i'm taking the gearbox out I should do something about the noisy input shaft bearing.... so i'm putting it off for a while.

Re exhaust, get the tuner to drop it at the front pipe to see if its an issue or not.

NSNPWR Rising Star

NSNPWR

Posted
  • Author
Posted

Cheers. Not exactly sure of clutch in mine, some cushion button thing with a billet flywheel according to receipt...hopefully holds up.

Should a full weight 32 GTR trap around 120mph with 300rwkw and a good launch? Or more? I'd like to think it would do that easy...

XRATED Veteran

XRATED

Posted
Posted

Buy a pair of rb20 afm's- they're direct plug in into the stock loom and will give you enough resolution for 380-400rwkw as well as being cheap. They're the same size as Z32's just half the price and no need to change the plugs.

You have injectors already... so why take the chance? Or sell them/swap them for smaller 550's.

I find it a little silly to take the chance at wrecking an engine for the sake of lazyness?

Cheers

Justin

NSNPWR Rising Star

NSNPWR

Posted
  • Author
Posted

Lol @ cheapskate...Running PFC, thanks for the tip mate, 20/25 AFMs arent exactly in abundance from browsing the forums?...

Like I said, im trying not to spend on it, nothing to do with being a cheapskate, have burnt plenty of cash on this and previous cars.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Lol @ cheapskate...Running PFC, thanks for the tip mate, 20/25 AFMs arent exactly in abundance from browsing the forums?...

Like I said, im trying not to spend on it, nothing to do with being a cheapskate, have burnt plenty of cash on this and previous cars.

Should be plenty around form people upgrading to Z32, Link/Vipec etc.

Plenty in NZ - have a look thruigh these ( I could probably get you a couple or three cheap and post them to you if you can't buy direct):

http://www.trademe.c...rch_suggested=0

XRATED Veteran

XRATED

Posted
Posted

Lol @ cheapskate...Running PFC, thanks for the tip mate, 20/25 AFMs arent exactly in abundance from browsing the forums?...

Like I said, im trying not to spend on it, nothing to do with being a cheapskate, have burnt plenty of cash on this and previous cars.

300 for a pair from any import parts wreckers???

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Lol @ cheapskate...Running PFC, thanks for the tip mate, 20/25 AFMs arent exactly in abundance from browsing the forums?...

Like I said, im trying not to spend on it, nothing to do with being a cheapskate, have burnt plenty of cash on this and previous cars.

Just remember they are still 2nd hand.

You could burn $300 on a 2nd hand set and then have them die on you a week later :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • isf
      HR34 GT speedo issue

      By isf · Posted

      The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Mine's a bit bigger at 70x150mm roughly. The spots are flat, just can feel the edges if I dig my nail into it. I did fix some other other ones by both using my finger to sand that small spot (I'm a bit wary of doing this and creating hot spots and a bigger mess) and I also did sand over it flat and others, but this also worried me a bit because if I create an overall low spot on the panel on paint that is good.  Correct me if I'm wrong but as long as it's flat even if I can feel the edges, I can put filler because it will all be level once I sand it? I can see myself going in a circle after sanding guidecoat with 320 grit if for example the panel is flat with my hand but because I sanded the guidecoat I could have created a low spot again somewhere. Unless where I'm going wrong is what I mentioned previously where I didn't go low enough on the grits. It's 1 step forward and 2 step backwards here haha. I'll probably need to experiment with it more. Last time I go back to bare metal lol.
×
×
  • Create New...