Jump to content
SAU Community

Recommended Posts

Hi

I have a 1996 harley fatboy in factory rare purple with white walls aftermarket pipes and ev13 cam,

The bikes immaculate and i dont get any use out of it so hence im looking for a car that i can drive around,

Im looking for a swap for a R33 GTR or a real sweet R32 GTR prefer NSW but will look at any offers..

Bike is valued at 19k ....

Email me on [email protected] if anyone is interested and for any more infor or pictures

Thanks

post-25886-0-85114300-1304074044_thumb.jpg

  • 2 weeks later...
  • 4 weeks later...
  • 1 month later...
  • 2 weeks later...

no offence but you wont get a 33 GTR for that, they go for high 20's low 30's. Better luck with a 32. They're closer to high teens, low 20's

  • 2 weeks later...

no offence but you wont get a 33 GTR for that, they go for high 20's low 30's. Better luck with a 32. They're closer to high teens, low 20's

Hi not havn a go at you but r32 gtr's are going for as low as 12k rough -20k for a real nice one and seen and looked at a few r33gtrs for 20k and i did add i will put some cash in.. i think carsales.com.au is where you should venture and see the real value now of GTR's sorry to say its a buyers market and lots of people are going to lose big time on there imports.. i know 20k will get me what i want and not in any hurry to purchase one..

Thanks for your comment

Lol no1 driving a gtr, will want to sit on a harley dude

?

what would make you say that? ive owned both harleys and a 33gtr so makes that comment a bit silly dont you think? Not everyone is a geek that drives and likes imports ,,

Anyways not here for a shit fight my ad states what i want and unless you have one please keep your comments to yourself.

Thanks

Edited by iwantone

?

what would make you say that? ive owned both harleys and a 33gtr so makes that comment a bit silly dont you think? Not everyone is a geek that drives and likes imports ,,

Anyways not here for a shit fight my ad states what i want and unless you have one please keep your comments to yourself.

Thanks

Ive got a R33 GTR and would love another harley (had a old shovel years ago haha)

might be intersted but would need 8K cash and harley

GTR is VERY VERY good. black, low k, almost immaculate inside and out

i really need a ute, but a harley...... mmm why not

let me know if your keen

im down the coast near Batemans Bay

post-50580-0-16299400-1313393910_thumb.jpg

post-50580-0-69495100-1313394298_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So left off with high hopes of having a gearbox in pretty quickly........ Got the adapter plate that week and had to chase a few threads and work out how/where everything goes as no instructions. Got the adapter fitted, test fitted gearbox and found had to cut and shave a few things. Tunnel required some hits with a decent hammer to give some clearance on passenger side but it fits with no problems,  could fit a 8hp70 with a little more work. For a cross member I wasn't going to spend $1100 on so shiny machined piece. Went through a few designs and remembered I had a gktech s chassis to cd00# cross member. Fitted that and found its close enough with a few extra bits welded so have gone that way and still a work in progress.  After this got into modifying the intercooler with some bends and clamps. I was procrastinating on this as was not keen to cut up and weld it myself but happy with the outcome.  Onto the radiator shroud and oil cooler mount. This thing took way longer than I thought it would but having to add an extra oil cooler for the trans and wanting everything within the chassis rails its good enough for now. It mounts to the chassis and gives plenty of room for lines and pipes. All the coolers are rubber mounted and sealed the shroud on the top and sides, will use some tape to seal the bottom gap of about 10mm. 20250508_111500.mp4   Next job was to build the new diff and after a delay with a friend got built this week. I ended up putting it all together with supervision and was good to learn how to set one up correctly. I ended up going a 3.69 ratio, nismo 1.5 way gt pro with gtr Axel's. Stripped it all down, gave all the parts a good clean, pressed on new bearings and set backlash. Was good working in a clean assembly room with all the gear. Once got home wire wheeled the case and hit it with some rollbar/chassis black paint. Got a few more bits done but will leave them for the next update.
    • That could be drilled, ground and welded. Would stop it progressing and leaking. But that block shouldn't be pushed very hard, as what you see there is a massive warning sign. But that fix also isn't going to happen properly with the engine in the car, and assembled. So you're looking at anew block if you're doing all that work anyway.
    • It's not as simple as it is being made out to be. It s not hard, but there are things that have to be done. Am busy right now, but will try to essay later.
    • Pinout is different to my knowledge, but you should confirm to be sure. Also you will need to adjust the VQ table in Nistune to suit. I would still recommend sticking with recirculating BOVs, I'm not sure if the R35 card MAF will fully resolve stalling caused by reversion/throttle lift.
    • What issues are those? Previous owner said it wants to stall sometimes. We did test drive and it was nice and smooth so it will be sporadic or idk. And if i just change MAF(the sensor to R35 version) it should be better? And as i asked...is it like "plug n play" with oem MAF from R34?  This is a MAF from R35 right?
×
×
  • Create New...