Jump to content
SAU Community

Recommended Posts

Got the following for sale:

Sard 700cc Injectors RB26 - $500 delivered

post-3189-0-10216800-1304765232_thumb.jpg

RB26 Dropping Resistor - $50

post-3189-0-48306100-1304765289_thumb.jpg

Gizzmo Shift Light - $100

post-3189-0-24204400-1304765306_thumb.jpgpost-3189-0-64121500-1304765321_thumb.jpg

R32 GTR rear brakes - $200 new seals 3500kms, endless pads, brake ducts, braided lines

post-3189-0-92650900-1304765338_thumb.jpgpost-3189-0-51923900-1304765352_thumb.jpg

Earls Oilstat - $150 thermostatically control your oil temp!

post-3189-0-41234800-1304765371_thumb.jpg

24 x RB26 Shims - $100 excellent condition, replaced with custom shims due to aftermarket valve springs / spring retainers

post-3189-0-60870600-1304765417_thumb.jpgpost-3189-0-99418000-1304765430_thumb.jpg

Pickup preferred postage at buyers expense.

Cheers

The injectors have done 3500kms and are up for sale as I upgraded to ID1000's to run E85 and more boost / pwr. As an aside these injectors supported 430rwkw with a single 044 external pump and factory fuel pressure with a sard rising rate reg. This was on a mainline dyno as well....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • ...oops. forgot the TCU end...
    • No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...