Jump to content
SAU Community

Recommended Posts

Hey guys, picked up this r32 gts-t to use the motor, box loom ecu, etc etc for my cefiro.

Parting rest of car out.

Has had a decent hit in front, moved drivers side strut tower over a bit, rail however looks straight. Im not a panel beater though. It is not written off either.

As above, im taking motor, loom, ecu, gearbox, alternator, power steer pump. Everything else is avaliable.

Interior is very neat, apart from wear on steering wheel and handbrake boot.

Rear quarters, boot, lights etc all in good condition, it looked like a neat example before it met its untimely death.

Some prices

Has stock exhaust from front pipe, rear muffler is a cannon, $250

Unknown brand front strut brace (straightend out one bracket) $50

Stock struts and springs (good for clearing defects) $200

Slotted rotors and front calipers with still heaps of pad left $300.

Blitz BOV with piping to suit r32, $100, with come with blanking plate for stock bov.

etc, etc,

Best to call or pm if after anything specific.

r32front.jpg

IMAG0603.jpg

r32inside.jpg

r32rearseat.jpg

r32strutbrace.jpg

bov.jpg

Alternatively, once I pull what I need out I'm after $1400 for the remaining car.

Located in Nowra NSW.

pm or 0400257530

Edited by CEF33Y
Link to comment
https://www.sau.com.au/forums/topic/363545-stripping-r32-gtst/
Share on other sites

Gearbox now for sale, $400

Rear lights $50 each

rear bar $100

Boot lid with stock wing $100

doors, complete with glass, trims, mirrors, switches $100 each

Stock front seats in immaculate condition $150 pair

rear seats in immaculate condition $100

Left hand headlight $50

Wheels in pic, 16's, with 225 50 16s yet to check exact sizes of wheel, guessing 16 by 7 or 8, with offsets around 35, tires average $300

Prices neg, to a point.

To anyone thats sms'd me and not got a reply, had to format phone, lost most contacts and msgs.

Whole car being stripped, so if after anything specific, sms, or pm

^^^clearly grey as can see in pictures.

i need glove box.

stero/ashtray surround if not broken?

that case/compartment 2x below the climate control.

inbay/engine stock cooler piping 2 pipes that go to stock cooler?

all delivered to vic 3029?

ps ..can put in a big box and use e-go for delivery...

in the boot where the fuel pump cover is there should be a squarish steel cover with two bolts in it. (covers the power plug) if it is there - how much with the two bolts?

if you need an image of it I can provide one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...