Jump to content
SAU Community

Tail ender

Revhead

By Revhead,
in Queensland

 Share

Recommended Posts

Mesmer Enthusiast

Mesmer

Posted
Posted

:wavey:

Well at least i've never come close to doing that again...

hope your car doesn't get laid too often you will never be able to drive it anymore :(

pssst slip i was too pissed thinking about my car and the repairs i just paid for and then how much revheads car was going to cost to be scared.

Plus people dont really get violent unless you act like a dick (like the guy this time).

John

Link to comment
https://www.sau.com.au/forums/topic/36361-tail-ender/page/2/#findComment-729964
Share on other sites
Revhead Grand Master

Revhead

Posted
  • Author
Posted

Hey Mes, how's things? If my car gets laid any more I think I'm going to start getting jealous :(

Ditto your last comment. Some people just cannot admit when they've made a mistake, and force people to want to kill them in the process :)

Link to comment
https://www.sau.com.au/forums/topic/36361-tail-ender/page/2/#findComment-730131
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...