Jump to content
SAU Community

Oil And Filter M35

Sage222
 Share

Recommended Posts

Sage222 Rising Star

Sage222

Posted
Posted

I did some searches and came across the part number for the filter.. Z436.. though what oil do you run in a vq25det?

i would imagine 5-35 or so though want to be sure. i only know the SR20det wanted 5/30 stuff was like water though necessary for that motor..

i have also read elsewhere that nissan recommend 7.5/30 for the vq35de.

Any other filter recommend than the ryco?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/363629-oil-and-filter-m35/
Share on other sites
  • Replies 149
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

bigkevracer Grand Master

bigkevracer

Posted
Posted

Same filter as a VQ35, I'm using a Nismo filter (http://www.gccorp.com.au/automotive/product_info.php?cPath=54_57&products_id=145). I think most people would recommend any other filter than Ryco. Nissan genuine filter has also been recommended to me. Part number I have here is Z445.

15W40 is ideal, although I think I'm using 10W50 at the moment, and no issues whatsoever. There are a few oils around that people like, Motul 300V seems to be the easiest to get (and dearest). I'm using Valvoline Synpower at the moment, and again no issues so far although its only been in the car 3-4 weeks.

Sunkist Grand Master

Sunkist

Posted
Posted

you can get a greddy filter from autobah.. same filters as s15 too.

im running 10w40 100% Synthetic GW(the last of the stash..)

at 285kw at the wheels. its the only oil that comes out like new when its time to change.. the equivelent is Motul 300v.. but thats big money.

bigkevracer Grand Master

bigkevracer

Posted
Posted

You sure its the same filters as S15? GCC listing says its the same as a SR20DE, but theres a different filter listed for SR20DET?

SR20DE: http://www.gccorp.com.au/automotive/product_info.php?cPath=54_57&products_id=145

SR20DET: http://www.gccorp.com.au/automotive/product_info.php?cPath=54_57&products_id=144

I'm running the SR20DE at the moment.

WAGON_BOY Mentor

WAGON_BOY

Posted
Posted

you can get a greddy filter from autobah.. same filters as s15 too.

im running 10w40 100% Synthetic GW(the last of the stash..)

at 285kw at the wheels. its the only oil that comes out like new when its time to change.. the equivelent is Motul 300v.. but thats big money.

the Motul is around the $45 for 5Ltrs isnt it ???

Commsman Veteran

Commsman

Posted
Posted

Discussion on the oil that one uses almost always ends in tears :ermm: . People get very opininated about type & frequency of service so I'm not saying anything.

However, Aaron, if your oil comes out looking like new you must change it too often :) . That Gulf Weestern stuff is good tho.

Sunkist Grand Master

Sunkist

Posted
Posted

i do change it too often lol but ide rather do it often with the power its running. i think the difference in filters is just the size..

ive asked for s15 ones and they've fit every time..

im using the greddy ones now though which are smaller but as long as youve got the thread right and the plate size right any filter within the size will fit..

s15 350z etc..

Dunc Mentor

Dunc

Posted
Posted

i do change it too often lol but ide rather do it often with the power its running. i think the difference in filters is just the size..

ive asked for s15 ones and they've fit every time..

im using the greddy ones now though which are smaller but as long as youve got the thread right and the plate size right any filter within the size will fit..

s15 350z etc..

As I understand it.. Filter size matters! It is used in establishing/maintaining oil pressure; changing the size of the filter changes the pressure it'll run at (higher/smaller volume..); too small and it'll be running a higher oil pressure. I could be mistaken though :unsure:

slippylotion Mentor

slippylotion

Posted
Posted

you can get a greddy filter from autobah.. same filters as s15 too.

im running 10w40 100% Synthetic GW(the last of the stash..)

at 285kw at the wheels. its the only oil that comes out like new when its time to change.. the equivelent is Motul 300v.. but thats big money.

If its coming out clean I would say your oil isn't doing a good job. Oils should trap contaminants that the filter will not. Every engine will get some amount of contaminants in the oil no matter how good you think your engine is.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If its coming out clean I would say your oil isn't doing a good job. Oils should trap contaminants that the filter will not. Every engine will get some amount of contaminants in the oil no matter how good you think your engine is.

Neither of us run that dino 98 fuel :P so the oil is usually a lot cleaner than usual(as are the engine internals), and the Sougi doesnt burn at all from what I have noticed even with multiple dyno runs seeing 110 or 120 degree oil temps. I have always changed mine at 5000 intervals using grade 5 oils only, call me paranoid but I prefer to be sure its at its best especially with the ethanol perhaps breaking it down a bit.

I used S15 filters when it was stock, now I need a larger rubber seal so I changed to a bigger M20 x 1.5 one that seats well on the cooler sandwich plate. Ryco have never let me down, unlike the Drift ones.

Sunkist Grand Master

Sunkist

Posted
Posted

pfffffttt!.....yeh travelling to QLD I'd have to carry Jerry can's....fun fun fun!....btw....when are you going to finish your tune :P

lol yeh i dont know. im trying to figure this boost control issue..im gonna pull the spring off the actuator n see if anything changes... but i have a feeling its the actuator not allowing "full travel" of the wastegate flap.. dont know why but ive opened up the wategate and nothing changed.

impul535w Community Regular

impul535w

Posted
Posted

Slightly off topic but kinda still on...

What do you guys use as far as the rest of the fluids? My M35 will be here soon and I plan on giving it a big service so I know where I'm at but just looking for advise as to what peopl run... Engine/Trans/Diff/Altessa?

Much thanks :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      They usually get made by hand as part of any such swap.
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      Was planning on getting an R35 MAF and the adapter, should this be okay? Also any idea where I could get my hands on an intake pipe?
    • joshuaho96
      Stock rb25det neo questions

      By joshuaho96 · Posted

      I mean yes, if you're starting from scratch on an unknown engine yes you don't need to be doing all kinds of math in the background but if you're doing relatively minor changes like AFM + injectors + boost up with some aftermarket turbos it takes quite a bit of math if you want to do something like maintain OEM fuel + timing tables but compressed and then a bit more load scale up top. I think I've spent too much time working on big engineering nightmares though so I'm a big fan of trying to constrain the scope of whatever work I'm doing as much as possible and trying to get it right before moving on. For example, a local owner just did the usual E85 + single turbo conversion to his R32 GTR and nearly burned his car to the ground doing some spirited driving up the local mountains. Turbine is unshielded and too close to the hood insulation. It's tough to balance "just get the project done" and "seemingly small details can cause massive setbacks I'm not willing to deal with".
    • soviet_merlin
      Neil's R33 Gts-t Build

      By soviet_merlin · Posted

      No idea about Neil's steering wheel, but I have the same behaviour in the Stagea. I doubt it has ever been messed with so might be normal. Indicating to turn right at a roundabout and correcting even a little bit to the left to go around will cancel the indicator. Never considered it an issue other than it being a bit odd.
    • silviaz
      Neil's R33 Gts-t Build

      By silviaz · Posted

      Does anyone know if this is off centered? Looks like it, when I indicate to go right, but turn my steering wheel slightly left it cancels (was always like that even before I started messing around with it) was wondering if anyone else has the same issue?
×
×
  • Create New...