Jump to content
SAU Community

Recommended Posts

Hello all skyline-ne-ans

Dex 3 was in gearbox when i bought the car beeen told that should do fine just change more often ... do wanna try getting back to tranzmax z but my head mechanic informs me that if i swap from one to the other it will fk the gear box

Mineral to sinthetic is bad plan.

I was wondering if i did the flush by disconecting the cooler pipe and flushed it like 3 or four times with tranz max z drop the sump and changed the filter then fill if that would be suitable

or as the boss said the only way to get rid of it all is "strip the bi**h"

Edited by simjim89
Link to comment
https://www.sau.com.au/forums/topic/363774-r34-auto-complete-flush/
Share on other sites

Drop pan, change filter then undo cooler return line, feed it into a bucket then run car constantly topping up trans while old fluid runs into bucket. You can expect to use a lot of oil depending on the condition of whats in there.

This will get 90% of old oil out but obviously there will still be some remains in converter, etc.

Won't hurt at all...

As for mixing fluids it sounds ridiculous but I have seen some cars come through the shop that drive like a dream then after a service, flush, whatever drive like crap for no apparent reason...

Saying that these were normally old cars. Wouldn't hesitate to change fluids.

Drop the pan - clean the filter (its a metal strainer) and put the pan back on. Pull off a line from the trans cooler and run the engine to fill a 2L bottle. Pour 2L fresh stuff down the dip stick tube. Repeat - it will take 12 -14L till it comes out clean. I used a Fuchs semi synthetic (can also use it for the power steering and Attessa if you have it so get a 20L drum ).

As for mixing fluids it sounds ridiculous but I have seen some cars come through the shop that drive like a dream then after a service, flush, whatever drive like crap for no apparent reason...

Saying that these were normally old cars. Wouldn't hesitate to change fluids.

That sounds like this (from the Castrol AU FAQ) - Its to do with putting new fluid (any new fluid) in a transmission that's running very old fluid, not about synthetic with non-synthetic.

"How to change the ATF?

I have heard that there are occasions when it is not recommended to change the ATF, but what are these?

It is not recommended to change the ATF in cars where no change has been performed for a considerable time (generally regarded as 50, 000Km from new, or 40, 000Km for K-cars), or where the maintenance history of the vehicle is unclear. Prolonged usage without an ATF change leads to a build-up of particles on the filter, resulting from wear of the gear and clutch parts, and of sludge, which accumulates as the oil deteriorates. An ATF change at this stage can cause these particles and impurities to circulate and jam into the shift valves or clog up oil ducts, creating more trouble. Furthermore, ATF changes are not recommended in cases of severe conditions of use such as towing or driving on punishing roads, or where there is an apparent problem with the Automatic Transmission operation.

Not changing the ATF can cause an increase in 'shift-shock' and affect system line. It is generally recommended that ATF changes are performed at regular intervals of 20, 000Km or 2 years, whichever is first, although manufacturers recommendations should be observed.

It is apparent that ATF has many important functions and must provide an extremely high level of performance. Recently the demands on ATF performance have been further increased with the rising application of Lockup Clutches in the drive for improved fuel efficiency. "

What world do they live in? 40K to 50k a long time? Most cars would be lucky to see an atf change ever. However the above article does reinforce the case against power flushing as offered by some auto shops as that is likely to lead to problems with seals etc. However overheated or burnt fluid is not good for your auto and a simple drain and refill is a good idea ( the whole 12+ litres not just the little bit in the pan).

  • 3 weeks later...

hey guys.

i'm attempting to flush my r34gtt auto transmission but need some tips on how to remove the trans sump.

so far i managed to get most of the bolts out but there are about 3 or four bolts toward the front of the car that are being blocked by a metal pipe (i think its about -4an or -3an).

how do i access those bolts that are blocked?

thanks

There should be 2 small metal brackets with 2x 10mm headed bolts holdings the pipes in places, take those bolts out it will allow the pipes to move a tiny bit. Then its just a matter of pulling the 4x pan bolts out, is easier to do if you use a 3/8 socket or even 1/4inch set.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...