Jump to content
SAU Community

[Sa ] 17X9 17X8 17 Inch Black 5 Spoke Rims, Avs / Advan Model 5, Perfect R32 Gtst Offset

Rolls

By Rolls,
in For Sale (Other Items)

 Share

Recommended Posts

Rolls Grand Master

Rolls

Posted
Posted

Got a set of rims for sale, they are pretty standard 17x8 and 17x9 black 5 spoke rims, no gutter rash and in good condition. They need new tyres as the sidewall on the front right has a gash in it but holds air fine and the rear ones are fairly bald. They will drive you to the tyre shop but they certainly are not legal.

Here are some pictures. Not sure of the offset but they sit perfectly on an r32 gtst, sit about half a cm in the guards so they are legal and fill out the guards well, no scrubbing or anything like that.

Can possible organise cheap 2nd hand tyres if needed.

skyline4.jpg

skyline3t.jpg

skyline1r.jpg

Can send interstate but will probably cost a bit.

Asking $350 ono

Can call on <removed> or PM on here.

  • 1 month later...
Rolls Grand Master

Rolls

Posted
  • Author
Posted (edited)

Yep sure are, they are 5 stud though, won't fit an R31 (assuming that's what they are for).

Edited by Rolls
  • 2 weeks later...
The Bogan Grand Master

The Bogan

Posted
Posted

$350, bargain, wish they were in NSW, can you get a quote on shipping please, if its not to much Ill grab them.

Post code 2173

Thanks Mark.

Rolls Grand Master

Rolls

Posted
  • Author
Posted (edited)

$350, bargain, wish they were in NSW, can you get a quote on shipping please, if its not to much Ill grab them.

Post code 2173

Thanks Mark.

Someone has just got in before you, if the sale falls through I'll let you know. Had them up for almost 6 months and finally two people want them at once haha.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      RB20 in need of modest love injection

      By Ozdavroz · Posted

      Do the R32s run high or low impedance injectors?
    • Duncan
      R32 GTST - 600KW+ RB28/CD009 Build

      By Duncan · Posted

      It may not feel like it to your wallet....but sounds like this was one of those "lucky you did it" rebuilds. Hopefully you have better luck this time
    • GTSBoy
      r34 gtt tall spoiler

      By GTSBoy · Posted

      It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
×
×
  • Create New...