Jump to content
SAU Community

Recommended Posts

I currently have a r32 gts-4 manual, and want to put an rb26 into it. Ive searched through the forums and the topics were quite old, so would like to ask some advice on going about it. Is it worth doing these days or would it be better to just buy a r32 gtr? My situation would be, if i were to put an rb26 into it, i would go to a workshop.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/
Share on other sites

isn't that rb25de as is? Uses Rb20 injection etc???

Logic tells me turbo it and save big dollars, then slam stocky gtrs with it.

just confirm what motor u have and when i get to a pc I'll comment further...

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828179
Share on other sites

I'm doing the Stagea swap. All wheel drive rb25, I agree with giving thought to a r 32 GTR. There is a lot of satisfaction in doing a swap, rb26s are getting cheaper. If you did both a rebuild and a transplant it will add up quickly. If you buy a 32gtr you could also be sorting out a motor and wear and tear any way. Most people will tell you GTR. I still think a gts4 with swap is interesting. With you Vic address have you looked at legalities of the swap? If you're buying a GTR why not get a later model 33 or better still 34 and just service it, a 32 is often a rebuild/restore etc.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828217
Share on other sites

Id honestly love to have a GTS4 over a GTR, there is a certain element of surprise that allures me.

Personally, having done the RB20 and 25 things in the past, Id probably try to pick up the shortest ratio diff I can and keep the RB20. Having a good turbo on it that will max out at something like 230rwkw would make for a very fun and respectable car.

If I had to have more, I would buy an RB25 donk and retune the exact above setup with non vct cams. That would unlock about 20kw more and all bolt back into place.

Doing an RB26 is probably going to set you back atleast 5k more than the above and will still be in stock trim... Only just faster than above if not at all.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829466
Share on other sites

The GTS4 gives you the cheapest all wheel drive chassis, which you own already. This is an example of the type of Stagea set up you could buy. An upgrade turbo or highflow turbo, could see you performing better than a stock tired GTR. Potentially you could have the GTR performance envelope, and more money in the bank.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=370511948278&ssPageName=STRK:MEWAX:IT

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829509
Share on other sites

get a neo rb25 instead, better than half the thrashed rb26s out there

ultimately just sell the car and buy one with everything already done to it

He would have to track down a Stagea Neo all wheel drive RB25, agree better cylinder head and rods.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829858
Share on other sites

I think the main point from the OP is that he'd be paying a workshop to do it.

Honestly, you may as well hand over your wallet, bend over and drop your daks.

I really can't see how you are going to come out ahead - $$-wise, kw-wise - getting a workshop to do the conversion. They charge for every hour they spend.

Even if you were doing it yourself in your shed it would be questionable. At least then the risk would be your time rather than $$.

If you are dead set on getting a GTS-4 conversion, wait for one already done to pop up, it's bound to happen.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830042
Share on other sites

If he buys an r32 gtr, a move which makes sense to me, when the engine has a problem, (quite often clutch electricals, ATESSA, suspension as well), where will he go? A workshop as many on this forum do. He could remove the existing engine and donor engine, with friends and an engine crane source parts, to control his costs.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830210
Share on other sites

Do whatever makes you happy, whatever you want more. Nothing is cheap, yet I would be damned if I could not beat a GTR with a GTS-4 dollar for dollar. Performance and reliability as said above.

GL

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832626
Share on other sites

If you picked a sensible power figure above a stock GTR, I'm sure I would get there more cheaply starting with a gts4, than buying a gtr and upgrading it. Similar to the post above.You already have a GTR chassis with an unflared body. Consider the nz gts4 below.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832703
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For your application, where you'll be at that 1/2" size or perhaps larger, yeah, excellent. Although not if you need a tight bending radius anywhere, because the corrugated stuff is not anywhere near as flexible as rubber/teflon cored stuff. But for turbo oil lines? No. Too big. They just don't do the corro stuff down at the ~1/4" ID size that you'd want, and if they did the OD of it would probably be a bit too fat for fitting it into the tight spaces available. I use hoses like that all the time for fuel gases (LPG, NG) and liquid fuels (HFO, diesels, waste oils). When we did the London Olympic cauldron, with the 204 individual burners on it, we had miles of the stuff (although a lot of that was teflon core). A bunch of that crap is still cluttering up the workshop, more than 2 years later!
    • Would something like this be an option  https://processhose.com/products/configurable-metal-hoses/1-2-in-t316-stainless-steel-annular-corrugated-configurable-flexible-metal-hose-assembly-with-ends-t304-single-braid-masterflex-af5550.html I'm looking at this for replacing the OEM EGR when installing a aftermarket intake plenum 
    • The once piece tail shafts with cv type joints on either end are the ones that end up vibrating and the vibration is caused by the cv joint binding as it turns, I’ve also seen them explode from the binding 
    • Take this with a pinch of salt, it's from someone (me) who got annoyed with turbos entirely. I hated aftermarket lines. If I had the option to use hardlines with whatever turbo I had - I would use them, 10/10, 100% of the time. The only reason people go larger, heat resistent, shielded lines etc is because they have to. And yes they don't last forever. Even if you spend big bucks on all the best heat shielding money can buy, with the best heat resistant, fuel resistant, oil resistant, radiation resistant hose, they get stiff and break down and just don't last the way a metal pipe will.
    • Unfortunately I am quite literally halfway across the globe. So all sources for parts like that are far away for me. What do you mean by that exactly?
×
×
  • Create New...