Jump to content
SAU Community

Recommended Posts

Driving Sport inc

Twilight Drift Friday the 3rd of June

Fusion Car Audio Sound off and show n shine

Driving Sports inc Twilight drift at Eastern Creek Raceway

turns 9 to 12 Entry fee 220 non members + CAMS $57 or ,180 full members

9 to 12 is a good news, bad news situation

The bad news for now is we have less corners , but it is a bit cheaper

The good news and the reason we can only run 9 to 12

is the track redevelopment is going ahead

So we can look forward to more and different corners in the future

EC have not given a exact time frame on when it will be finished

as we have more info we will keep you updated

Driving Sports inc Twilight drift at Eastern Creek Skid Pan (wet)

Entry fee $150 + CAMS $57 non members ,$110 full members

Driving Sports inc Twilight drift at Eastern Creek Figure 8/peanut (dry)

Entry fee $150 + CAMS $57 non members ,$110 full members

You can chop and change between the wet pan and figure 8 when you like

Passengers in cars with out a cage on the wet skid pan is ok .

Minimum cams approved half cage for passengers on the figure 8 and main track

FUSION car audio

Sound off Entry Fee =$ 30

Show n shine Entry fee =$ 20

Entries will be capped

So book now

please do not wait till the last minute pre paid entries will only be accepted up to Tuesday the 31st may

so send a deposit now and lock in your spot before we are full

Entrants for on track activities will receive one pit crew pass and one pit/ paddock car pass

On track activities start at 6:30 pm and end at 10:30pm

Scrutineering. For entrants starts at 4:45 pm at gate 7

Heaps of action for drivers and spectators With 3 different dedicated drift areas, DJ and light show in the pits , sound off show n shine , give a ways/prizes, hire a drift car plus more

Entry fee $20 for spectators kids under 14 free

To book go to www.drivingsports.com.au and fill in a entrant form

Or if you would like more info email us [email protected]

if you have never been out to one of these follow the links below

for pics and vids

thanks to Matt everingham for the pics and blog

http://mattheweveringham.com/?p=639

thanks to jason from redbak photo for main track pics

and kory for the pan and F8 pics

http://www.koryleungphotography.com.au/gallery/DSEC20110430/index.html

.

Edited by KLR33


  • Similar Content

  • Latest Posts

    • Nissan/Pitwork is fine stuff. HKS is just marketing wank. I personally wouldn't do the idler if it is already new. If it looks and feels fine, it is fine. But as D says - it's cheap to add it to the job. The water pump ditto. Even more so. If it show no signs of problems, then it is nearly new - leave it.
    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
×
×
  • Create New...