Jump to content
SAU Community

Flat spot/Power Loss

Terminal

By Terminal,
in General Automotive Discussion

 Share

Recommended Posts

Terminal Grand Master

Terminal

Posted
  • Author
Posted

hmm... the coils seemed to be fine when i checked them, i did the coil test by disconnecting one and seeing if the engine kept firing or not. i guess ill have a closer look. i wouldn't expect water could get down that far, but one of my coils was wet. ill have another go at them i suppose. i replaced the plugs, so they're fine

Terminal Grand Master

Terminal

Posted
  • Author
Posted

Heh, aren't i red faced, my AFM was clogged with my air filter. its completely buggered, falling to pieces etc. thanks a lot for all your help though guys, at least i know what to look for next time.

ENTYSU Collaborator

ENTYSU

Posted
Posted

ok going by my experience, a few cars i did had symptoms you had ,

FAULTY AFM.

FAULTY TURBO (Bearings or bushes and shaft wear )

FAULTY plugs

FAULTY coils

FAULTY governor valve on side of planum

FAULTY fuel reg and or pump maby filter test with fuel meter

FAULTY crank angle sensor and or knock sensor

LEAKING BOV, pipes , intercooler.

clean out all harneses that may have came in contact with water especially crank angle sensor and knock sensor ...

proccess of elimination mate start from least expensive too expensive .

Jay95R33 Grand Master

Jay95R33

Posted
Posted
Heh, aren't i red faced, my AFM was clogged with my air filter. its completely buggered, falling to pieces etc. thanks a lot for all your help though guys, at least i know what to look for next time.

D'oh - oh well, it's good you got it sorted out.

Hay if you've got a stock airbox and need a stock filter element, I've got one you can have for nothing.

J

Terminal Grand Master

Terminal

Posted
  • Author
Posted

I've actually got an HKS Pod, it came with the car, but the filter is stuffed now.

I'm actually thinking about getting a stock airbox reinstalled and a high flow filter, is there any difference between this and a Pod? i don't want to lose power, but the Pod is so bloody noisey

Jay95R33 Grand Master

Jay95R33

Posted
Posted
I've actually got an HKS Pod, it came with the car, but the filter is stuffed now.

I'm actually thinking about getting a stock airbox reinstalled and a high flow filter, is there any difference between this and a Pod? i don't want to lose power, but the Pod is so bloody noisey

Well, when I got my car it had a HKS pod filter too !!

I went from the HKS pod that was in a cold air box, to a stock airbox with a high flow panel filter.

The only difference I found was that it was 10 million times quiter...... I noticed no difference in power at all.

With the highflow panel filter I can still hear a little bit of induction noise, and I can hear the turbo spool up now (really high pitched whine, that goes so high it goes out of range of your hearing :D ) but it's 100% better than the HKS pod.

J

Jay95R33 Grand Master

Jay95R33

Posted
Posted

Little bit of induction noise..... That's not a HKS pod filter. They are one of the loudest pods around.

I actually found it pretty anoying. Taking off normally it'd sound like your were going flat out.

Much nicer to drive with the stock box with a high flow panel filter.

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      2025 Osaka Auto Messe

      By r32-25t · Posted

      I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • Rezz
      2025 Osaka Auto Messe

      By Rezz · Posted

      $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Dose Pipe Sutututu
      R32gtr sputtering and stalling

      By Dose Pipe Sutututu · Posted

      Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • joshuaho96
      R32gtr sputtering and stalling

      By joshuaho96 · Posted

      I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...