Jump to content
SAU Community

Recommended Posts

Hey Guys,

Thought I might slap up my R32 for sale. It needs a little bit of work to get going properly but is cheap for whats included.

I bought the car with the intention of turning it into a track car, didn't even want an R32 but bought it as it was advertised to have had a full rebuild with receipts which I found wasn't true. Since then I have just lost interest in it and want it gone. To be honest I don't even know that much about the car! I'm currently building a track R31 so this is just sitting taking up space.

Details on the car:

1992 R32 Skyline

5 Speed Manual (Apparently R33 Box)

"Twin Plate" Clutch (Awesome Clutch. Very bitey, but doesn't make the chatter of a twin)

Front Mount Intercooler

Stainless Intercooler Piping

Full 3" Turbo back exhaust with custom dump & front pipe. (Exhaust has 1 mid muffler and end cannon. Sounds awesome and is quiet! Can get a sound clip if anyones interested)

Greddy Blow Off Valve

Gizmo Electronic Boost Controller

Apparently GTR Sway Bars (Haven't had callipers on it to check it out)

Apparently R33 Turbo (haven't been able to verify as I'm not sure on the differences between the 2)

Fuel Pressure Regulator

Lowered Springs and Shocks

Blitz Turbo Timer

Momo Steering Wheel

Momo Pedals

Interior is in awesome condition. Exterior is pretty good, but does have a few small dings and scratches. Front bar has a fair few stone chips.

Bad Points:

The car runs, but there is something wrong with it. It sounds like it is over fuelling or fouling. Drives up until about 4k where it fouls with any hard throttle. I've changed the plugs with brand new NGK ones and coilpacks with known working originals and still no avail. At the worst, a replacement RB20DET is cheap as chips anyway. More than happy for anyone who is keen to come and inspect the car. I'm getting the car looked at shortly by a mechanic so may be fiixed by then. Next thing to check is the actual ignitor but have to source one first.

The fuel tank has a small hole in it. Must be right up the top because it only came out when I fully filled the tank

Air Con Removed

No Rego

Theres a bit of road / land where the car is being garaged where legitimate potential drivers can take it for a drive to check out how it drives.

Any questions, PM me or call / text Blake on 0437480958

Price is $5000

Or Swaps for a Canon 5D Mark II + Cash!

Located in Wagga Wagga, NSW

(Only have a few photos of it. PM Me if you want some more)

184386_1869893786982_1230234672_32261661_5435672_n.jpg

183377_1869894146991_1230234672_32261662_684097_n.jpg

183800_1869894466999_1230234672_32261663_1315082_n.jpg

182761_1869894827008_1230234672_32261664_6717506_n.jpg

dsc0696f.jpg

dsc0029dp.jpg

dsc0028t.jpg

  • 1 month later...

Bump

Nope haven't had the car looked at. If I do fix the problem, the car will go up in price. It's cheap as it is with RB20's going for next to nothing in a worst case scenario

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You know, that is exactly the thing that I was thinking a coupe of hours ago. I even had a plan for a meme, involving one big one, another big one, and the Old El Paso girl saying "¿por que no los dos?"
    • NoS, 2 of the big ones.
    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
×
×
  • Create New...