Jump to content
SAU Community

Recommended Posts

Hey guys.

My car was doing something strange yesterday.

It started going lean and popping at idle, at normal operating temp, so I grabbed out my hand controller and my LC1 was telling me it was running about 18-20AFR!

Everywhere else was fine, under boost, cruising above 2000rpm etc, all fine, but as soon as the revs dropped below 2000rpm, coasting with no throttle and idle conditions caused the pop. Coasting down in gear under 2000rpm made it pop like mad. It's as if anything below 3mS of fuel became unstable, like I was running 1000cc injectors lol

It usually takes about 2.0mS of injector to get 12-14AFR at idle depending on ambient temp, but yesterday I needed 20% more fuel, 2.4mS gave me 14-15AFR with the occasional pop and 16-17.

Does anyone know what this sounds like? Keep in mind I havn't changed anything before, all I've done was install some LED angel lights, which weren't even on at the time.

dying fuel pump - unlikely, the pump is only 18 months old

blocked fuel filter - possibly

dirty injectors - maybe

bad batch of fuel - maybe, I filled up at Gull using their 98, which I had never done before!

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/365739-random-leaning-idle-and-coasting/
Share on other sites

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

Sorry not much info... haha

EMS Stinger - map sensored, no TPS.

Engine is a QR25DE+T

returnless fuel system, walbro pump, 440cc WRX injectors, stock everything else.

I'm not sure if it's a one off, I havn't started the car up today, just been sitting here studying all day - ill report back when I go for a drive later.

There's two situations that it does it, at idle, and coasting down in gear at low revs, both occur at low throttle, below 2000rpm.

it's odd because it's never done this before!

Does it sound like anything common?

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

That's exactly what my car is doing!

Aside from the current leaning problem, my car has always had an issue at around 1700rpm, you have to apply load very smoothly, otherwise it'll buck down and die, I've tried adding up to 40% more fuel at these points and it does nothing. As long as the car's had the EMS there, its had a problem at 1700rpm, but now since this new tank of fuel, it's developed this weird leaning condition.

Actually thinking of it now, the servo that I filled up at was a United. Up until last week I've avoided them because I didn't know they sold 98. But last week I filled up with their "98" for the first time. I'm leaning (pardon the pun) towards bad fuel...

Frankly, I wouldn't be worrying about running so lean at idle. It will not damage the engine at all, because there is virtually no load on the engine.

As for the popping, have to set up the EMS to shut off the injectors when the throttle closes (such as when you coast down, or change gears)?

Doesn't have an idle map as such, it's got a separate function for idle control, then I've just tuned the points around idle for 12-14 ish, then air temp and water temp correction values take over from there too, none of which I had changed before it started going wierd. Has no TPS.

Dont know what fuel pressure is doing, I dont have a fuel pressure gauge, if it starts going wierd again I'll look into it further...

Went fir a drive yesterday and it's all fine again...

Loose wires somewhere?

I cleaned up all the mess behind the head unit yesterday, coincidentally it stopped being wierd, but all I was doing was cable tieing things up, besides there's nothing behind there to alter fuel control...

Anyway thanks for your help bros!

Okay so the problem surfaced again today, and today was the same type of day. It's got something to do with overcast humid days. Not necessarily hot vs. cold, cos it runs fine at night and during a hot day. Maybe humidity plays a part?

i'm gonna do a fuel filter, run some injector cleaner through and install an air temp sensor and tune some air temp comp maps, see what that does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it's for a SR20, make sure it's not the American Poncams, might as well call them Poocams. Had a set in a friend's car, all scuffed up after a few track days. Like the metallurgy Tomei USA used is junk. Went back to JDM OG Tomei Poncams, no issues till now.   Tomei USA is not the real OG Tomei.   Random rant over, fk the US of A, bunch of c u n t s. 
    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
    • Hello. I have an a31 cefiro but since I am in Turkey we have a CA20S engine. I did some research. Then I found that I can swap with a ca18 but when I heard that it has the similar substructure as the s13. I thought I can swap with an sr20 because the sr20 was used with the s13. So can I easily swap the sr20 on my cefiro or is it difficult? 
×
×
  • Create New...