Jump to content
SAU Community

Recommended Posts

I also bow before the awsome knowledge and experience of Sydneykid. And he is such a nice guy too.

If all the people that he has helped each shout him one very small beer, he is going to die of alcohol poisoning.

Cheers to Sydneykid, my hero................

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Although this sounds a little like an obituary.."god forbid" I'll throw in my 2.2cents inc GST.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  

Hi MIC33R, You Said

"yep, without SK, I wouldn't know half as much as I now do about Skylines or even cars in general."

:) I'd like to start with the reason why you didn't know that much.  I have pretty good success using this formula to determine the reasons;

Brain in lbs per minute = diameter of cells in mm X knowledge correction factor

So let's apply it to you;

300kw @ the brain = 480 brain power

480 brain power = 44 lbs of airflow = 44 mm of brain

Now if you want to run 19 psi of air through your mouth, then that's means you'll need to read that amount of my threads.

But we need to apply the brain boost correction method....  

My experience indicates that to get 300kw @ the brain, out of a newB sau member you would need to run around 1.5 bar (22psi). So using the formula...

44 / 22 X 19 = 88mm of brain. In other words, you're only half way there.

Summing up, I think you guys have a numbers of problems, mainly your mouths are to small to soak up the grog and your fat % per capacity intake is too much, So you guys get Blotto on the smell of grog. To bypass this I would recommend springing your "mouth" using a 2bar mouthgate & attach an non returning blow off valve through the anal passage.

[/b] [/size]

I'm not so sure I should trust your advice, but what the hell. One 2bar mouthgate coming up :)

BTW I didn't even know my brain could be boosted. Thanks for the tip!

Son of SK here

You guys should try living with him... geeeeeez Threads like this should be banned, now he has an ego... pppfffttt, like he didn't before.

I'll thank ya'll on behalf of him. :boobies2:

Just hope he doesn't get poached

:ufo:

Hey is that the RB31 powered weapon we keep hearing about in your avatar SOSK? That chassis has a bit of attitude...I can almost see daylight under the left front :D

A gallery of the car(s) would be nice if you could put it up.

Hey is that the RB31 powered weapon we keep hearing about in your avatar SOSK? That chassis has a bit of attitude...I can almost see daylight under the left front :)

 

A gallery of the car(s) would be nice if you could put it up.

Yeah, i wouldn't mind knowing which series it runs in either, so we can follow the performance and results of that car!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...