Jump to content
SAU Community

Recommended Posts

Pick up Morphett Vale, SA 5162, or will post for $50 cost Australia-wide

For Sale:

Tein Suspension

Fixed Height (non-adjustable)

in good condition, from R32 Skyline GTs-T

$400 pickup, $450 posted

WP_000040.jpg

PM me please

other items for sale, postage approx $20:

1x pair stock R32 RB26 GTR manifolds $100 the pair

1x pair stock R32 Rb26 GTR turbo dump pipes $100 the pair.

1x 5-point clip-buckle harness, brand RCI. $50

1x r32 rb26 GTR oil pump, used but in good condition $50

1x r32 RB26 GTR harmonic balancer, in good condition (used) $80

1x oil catch can with mini pod-filter, brand new, $50

1x 3-guage holder set, new. $30

2x Q45 Air Flow Metres, Working condition, with plugs. $100 the pair, or $50 each

1x Z32 Air Flow Metre, working condition with plugs, $100

1x pair pod filters. Brand new never used. $50 the pair, or $30 each seperately

1x stock R32 RB26 GTR Intake pipwork, $50 the lot

1x stock R32 RB26 GTR coilpack cover blue, $100

1 x stock R32 RB26 GTR turbo two-into-one exhaust front pipe, good condition $50

1x 3" decat pipe with flex section, brand new never used $60

1x 3" twin barrel mid-muffler resonator section, brand new never used $80

I'll redo another picture, sorry, damned phone camera!

They sit nicely with around 2 finger width between guard and tyre...... a good inch clearance

as per below when fitted to my R32

rbside.jpg

rbrear.jpg

advertised this gear on ebay recently.

tein shocks one ebay listing, all the rest in a group lot listing.

need to sell, house is sold now so must clean out all parts I no longer need

only have these items left:

1x pair stock R32 RB26 GTR manifolds $100 the pair

1x pair stock R32 Rb26 GTR turbo dump pipes $100 the pair.

1x stock R32 RB26 GTR turbo two-into-one exhaust front pipe, good condition $50

1x r32 rb26 GTR oil pump, used but in good condition $50

1x r32 RB26 GTR harmonic balancer, in good condition (used) $80

1x 5-point clip-buckle harness, brand RCI. $50

1x oil catch can with mini pod-filter, brand new, $50

1x 3" decat pipe with flex section, brand new never used $60

1x 3" twin barrel mid-muffler resonator section, brand new never used $80

1x full set Tein suspension to suit R32 GTS-T. Came out of four-door R32. Tein shocks/springs. In good condition $400

post-18854-0-60614600-1307594159_thumb.jpg post-18854-0-51858900-1307594217_thumb.jpg

5-point harness sold.

I need to move this suspension on, offers accepted. Was $400, offer me $300 and they are yours.

Bargain

  • 5 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...