Jump to content
SAU Community

Recommended Posts

I'm thinking about turning my R32 into a drift car instead of trying to sell it.. I have the following shopping cart planned but my friend said I needed a few extra things.

My currently planned list:

  • Coilover Suspension
  • Suede deep-dish steering wheel w/ boss kit
  • sparco seat
  • fmic
  • LSD

However he's informed me that once I upgrade from wet roads to dry roads, I could risk twisting my chassis unless I install something like that brace that runs through the center of the car.

So that said, what else am I going to need for getting into dry road drifting (obv. I'm talking track)

Edited by SKITTLES
Link to comment
https://www.sau.com.au/forums/topic/367017-whats-needed-for-basic-drift-setup/
Share on other sites

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Lets see... what did I do to my car to make it driftable... I think I took it to Oran Park... pic related

n639839121_1630968_4930.jpg

On a more serious note, swaybars will make your slides easier to catch. Other than that you really don't need much, especially if you are just starting

basics

-locked diff. sure you can get a 1.5 or 2 way LSD but they are expensive and not required. Lockers aren't perfect but it's a drift car, not a time attack race car.

-a working clutch

-skid rims and tyres.

-remove HICAS

-alignment.

extras

-coilovers

-swaybars

Power isn't needed. You want the car to handle well and be predictable. Save funds for repairs, servicing and tyres.

Car damage is apart of drifting.

Edited by Peter89

So much torque, the chassis twisted coming off the line

win-one-internet.jpg

if it's a r32, an rb25 will be a good place to start, lol

*waits for all the RB20 fanbois to get sand in their vaginas

The original plan was to put an RB25 into it, seeing as the engine has 227,000KM on the clock. But the existing RB20DET is going stronger than my RB25DE with 165000km...

basics

-locked diff. sure you can get a 1.5 or 2 way LSD but they are expensive and not required. Lockers aren't perfect but it's a drift car, not a time attack race car.

-a working clutch

-skid rims and tyres.

-remove HICAS

-alignment.

extras

-coilovers

-swaybars

Power isn't needed. You want the car to handle well and be predictable. Save funds for repairs, servicing and tyres.

Car damage is apart of drifting.

12293_380244637013_520517013_3901770_4183248_n.jpg

This is pretty much my favorite pic atm.

Thanks for the tips though, I think I'll get a locker and use that for a bit before getting a 2 way lsd.

I don't know if it's got hicas, but i'll check it out tonight.

who teh fark said the chassis will twist and that you should out one of those pointless floor bar things in the car?

Well actually, the chassis will twist/flex a bit as soon as you sit in the car.

You callin' me fat? :P

So the floor bar thingo is pointless?

locked diff, no need to spend $1000+ on a LSD when a shimmed diff will do the same thing

a good seat, Velo seats are great and can get them pretty cheap

make sure the handbrake works to:P

thats all you need to start, anything else is pretty much extra

steering rack spacers are win and cost next to nothing

there are some basic engine mods that will help a lot (fmic, exhaust and more boost)

go watch some in car drifting videos, helps a lot at least knowing what you need to do

I was thinking of getting a $400 pair of seats hahaha just el cheapos... wonder if they're any good >.>

Yeah, gotta change the brake pads. I'll have to do the rear brakes, they don't seem to be grabbing the wheels too hard.

newbie question here,

Do you need any surge tanks or to change to a different sump, just wondering when your flying sideways wether theres still enough oil and fuel going in??

as long as you don't run low on fuel it shouldn't be a issue, stock sumps are fine to

Seriously, just drift it as it is. If you don't like an aspect of your car you will either quickly find out and change it or learn to just deal with it. Standard cars aren't undriftable, it's just harder :thumbsup:

Though... just to contradict myself, it is handy to have something to hold you in place. In my experience a harness with a factory seat works much better than an aftermarket seat with a factory seat belt. Grabs less attention from the police too ;)

Seriously, just drift it as it is. If you don't like an aspect of your car you will either quickly find out and change it or learn to just deal with it. Standard cars aren't undriftable, it's just harder :thumbsup:

Though... just to contradict myself, it is handy to have something to hold you in place. In my experience a harness with a factory seat works much better than an aftermarket seat with a factory seat belt. Grabs less attention from the police too ;)

Interesting thought about the harness....

As for leaving stock; the R32 has a lot of body roll and whilst it's still very driftable (not that I'd know >.>) it's a little unpredictable. Easier to stiffen the suspension and put some sway bars in before I head out.

Due to money, I can't get out on the track fo ra while, so might as well save up in the meantime for the gear.

newbie question here,

Do you need any surge tanks or to change to a different sump, just wondering when your flying sideways wether theres still enough oil and fuel going in??

For future reference; I've never had an oil problem with the car sideways, but I've only done it a couple times and was too busy watching other things.

I DO know, however, that when I was testing the brakes in it, I smashed them to the floor and the oil pressure (or whatever it is) guage suddenly dropped and the car almost stalled.

oil level might have been low.

for all RB's it pays to overfill the sump by half a liter.. cant go wrong with that. same with fuel in the tank. make sure its over half and there wont be any issues.

as for whats needed.. just an LSD that works.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not R7R. Meant to type R&R, obviously enough.
    • Bugger "making it look stock". I put one conventional internally fused Hella relay behind each globe. I just pulled the plugs off the back of the globes and built new loom segments with male and female plug parts to match up to the original loom and the globe, and used the original power wires to each globe coming from the switch through the original loom plug to trigger the relays. Ran a big fat (also separately fused) power wire across the front of the car to feed all the relays. It's as ugly as f**k, but it is wedged down between the headlight and battery on the RHS and the airbox and headlight on the LHS, and no-one ever looks in my engine bay, and on the odd occasion that they do I simply give no f**ks for what they think. Fully reversible - not that you'd ever want to. For f**k's sake. It's a Skyline. They made million of the bloody things. We've been crashing them into roadside furniture for 30 years now. There is a negative side effect to putting relays on the headlights. The coil current is too little to properly clean the contacts in the switches and they get blacked up and you have to open them up every couple of years and clean them manually. I have 25 years of experience on this point.
    • I was poking through the R34 wiring diagrams vs R33 and noticed that the R34 has proper headlight relays while the R33 is like the R32 and sends full headlight power through the headlight switch. I'm not afraid of wiring but I really would like to do this in a way that looks OEM (clipping into open positions on the OEM relay box) and also unlike the factory wiring which interlocks the high beam and low beam on the halogen series 1 GTR headlights I want to make it such that turning on the high beams keeps the low beams on as well. Any advice on how to locate the specific connectors + crimp terminals + relays I need? I was thinking one NO relay for low beams and another for combined high + low running off the factory high beam headlight connector. I don't really want to splice into a crusty old probably discontinued factory harness so fully reversible is my goal here.
    • Pretty sure they run the same engine as the Q50 hybrid which specifies 95 RON.  I ran 98 in mine for a while, but it made no difference in performance or economy, so I have been using 95 for the last few years.  I have never hit 6.0L/100km, but have returned mid to high 6 on the highway.  Being a hybrid, fuel economy is a lot more dependant on how you drive it.  At 110km/h, mine never goes into EV mode on the highway, so returns closer to 7.5L/100. urban driving can return low 8s if you are careful or over 10 if you are a bit more enthusiastic on the throttle.
    • About a quarter of what you want to do. It's only R7R, not R&dismantle&replaceparts&reassemble&R. ? It is stock. I already told you, you will NOT have broken those. It's f**king 4th gear for Christ's sake. You just chipped the teeth off.
×
×
  • Create New...