Jump to content
SAU Community

Recommended Posts

  • Replies 163
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

It's at the end of The Hume Highway where it splits off into Cambelltown road and Camden Valley Way. There's a Bing Lee near it, hard to miss

Hey is there an address i can pop into the GPS that will take me to the meet up point? I don't know my roads well around that area.

[EDIT] The meet up point is at the KFC on the Corner of Beach Rd & Parkers Farm Place right?

thanks.gif

Edited by choongy

Haha dont worry i aint like the other 17 year olds, mummy or daddy didnt buy me a skyline for my birthday. I worked and saved for it, so im gonna look after it.

I'll be on my best behaviour :D

Of course youre welcome. All are welcome. Thats what its about. Just gotta love your cars and great company and your good to go:)

decided to bring the 200 out again... for anyone already down south, we'll meet up in front of the school next to St. Paul's catholic church along tongarra rd again.. Wont be the same without owen banana.gif

decided to bring the 200 out again... for anyone already down south, we'll meet up in front of the school next to St. Paul's catholic church along tongarra rd again.. Wont be the same without owen banana.gif

Sounds good. Do you wanna PM me your number so i can keep you up to date with the syd people if there any delays ect?

Just been in discussion with 'wannabedrifter' and we will leave cross roads at 10.30am sharp so we can meet up with the guys from sth coast in time. What time, i dunno, check with 'wannabedrifetr'

Thanks

Hi guys. The meet up for the south coast cars will be on the corner of Illawarra Highway and Macquarie Street. Lets plan to be there by 12pm. any questions just pm me. cheers

post-78424-0-59468500-1308047852_thumb.jpg

Gem you have to change your pic hope you kept something from the princess

Hellya!!! I kept the pink seat covers as my mascot the lil fairy that hangs from my mirror:) I am sad that i didnt get a turbo but i needed to think $$$$ and the GT was just outta my reach:( Don worry thou, when i win the lotto ill give Terry a run for his money:):)

I'll be there too.

Gonna be @ Cnr Beach Rd & Parkers Farm Place, Casula NSW 2170 @ 10am on July 2nd. Can't wait!

I drove through Royal National park all the way past Bulli but I never went past the Gong. I'm looking forward to a nice chilling cruise with respectfulness and turning corners really fast :D




  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...