Jump to content
SAU Community

Recommended Posts

I noticed yesterday that my clutch is leaking a lot of fluid from where the shaft (the one kinda attached to the clutch pedal) goes into the master cylinder.

I'm guessing a seal is gone, but can anyone offer up any advice asap. Is there anything I can try short of taking it somewhere because I'm a bit short on funds atm :

Thanks

46n2

Link to comment
https://www.sau.com.au/forums/topic/36757-help-asap-cluch-leaking-fluid/
Share on other sites

  • 2 weeks later...

Funnily enough - I found that exact problem today as well. I have clutch fluid dripping down onto the clutch pedal and the floor. It's not leaking very fast but I had to top up the fluid today - I caught it when it was about 2mm from the bottom of the fluid reservoir.

46n2 - is the fluid leaking inside the car like mine?

MearCat : Yeah, it's leaking inside the same as yours :D I've spoken to a few ppl and they think i'll be in need of a new master cylinder. I'm holding off for a few days to confirm. I'll post back and let u know...

46n2

  • 2 weeks later...
  • 4 weeks later...
  • 7 months later...

nooooo. $250 ouch....

in future guys.....

go to your local clutch place. and ask for a rebuild kit. should be about $10.

it will be a rubber seal. then you just replace the rubber seal on yours. and bolt it back in.

thats all that is needed to be done. i had a problem on mine and i solved it this way.

if you dont want to go to the hassel of rebuilding it...

i have got a spare one i'd sell.

it doens't leak. i doubled up when i didn't know what to do...

hehe...yeh i've got the same problem.....always a wet patch on my floor mat under

clutch pedal...and refillin the clutch master cylinder every couple of weeks.....

anyways...like dabigbolf said....i went and got a rebuild kit from nissan...

only cost me $40..

kit contains complete piston, return spring, piston stop ring, o-ring and the boot - all brand new....

if you going this way best idea is to give the cylinder a nice honing to insure the seal beds

in smoothly..

$250 is a bit steep....so $40 and a lil diy is ALOT lighter on the wallet......

Clutch Master Cylinder.

$250 is a bit of a RIP.

I bought mine for around $60-$70 from a local brake/clutch shop in St. Mary's.

It is made by PBR.

I may be able to dig up some old photo's of the box & part number.

Bl4ck32 also recently replaced his and knows the exact price as I replaced mine 2.5years ago.

Also guys remember when taking on the $40 kit rebuild option - IF your master cyl has scores in the bore it will need to be re-sleved or replaced which will end up costing you more money in the long run.

So before you buy the kit - it may be a good idea to take the master cyl off and taking it to a clutch place for assesment before spending your money.

I have encounterd the same problem on another car we had used that was 15 years old and from japan.

Does the clutch slip when powering down from 1st to 2nd when you shift really fast, once you back off quickly ( when you noticed its slipping ) .and give it gas it stops slipping ?

If thats the case, your stopper for the clutch pedal can be the problem.

petar.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Excuse me, but 2) does apply 1) Would also apply if you consider how much is spent in the alternatives. Also there's the option of 3), buy one pre-built that you can put your family in (it's me, it's my car)   That said, I went on a ~500km drive the other day. I didn't use anything more adventurous than 3rd/4th gear at about ~3000RPM and 50% throttle and I was going as fast as anyone has any sense doing on a public road, with enough grip to the point where I didn't want to go any faster. I was obviously under the limit of the current car etc etc. MX5 with 2.5 N/A to achieve the same speed would be more fun for any road scenario. Maybe consider cams. I wouldn't boost it. The use case is just not there and it won't actually make the car more enjoyable unless you really do plan on wringing gears from 1st to 3rd (at least) at 100% WOT on a public road to 150+kmh.
    • Great if: 1. You had all of the money for everything else that is required  2. Lived in a country where you could actually do this and drive it legally on the road Sadly, neither applies to me As for the turbo, I am having second thoughts, mainly for engineering/registration legality reasons and insurance  Not saying I've finished doing stupid things that I probably should do to the MX5, but boost, and V8 engine swaps isn't on the cards Strange, but true 
    • I like this page, better than that silly turbo kit   https://v8roadsters.com/product-category/engine-conversions/engine-conversion-lsx/engine-conversion-lsx-nc/  
    • That would be my Shoei helmet
    • Yes shipping here can be a pain, was about to purchase timing belt replacement kit, but it tends to get expensive due to shipping (and customs if importing from non-EU which the UK now falls under).
×
×
  • Create New...