Jump to content
SAU Community

2860-7's, Rb25 Afm's, Dumps, Cat Fwd, 4X Cas, Swap Hi Mount

Dabro
 Share

Recommended Posts

Dabro Collaborator

Dabro

Posted
Posted

Hi All,

Going big single and having tidy up.

2x 2860-7 Turbos done about 15k. $2000

4x CAS units, one has the drive sleeve taken off. $75 each

2x Lower OEM R33 GTR intercooler pipes with protective cover $50 for both.

2x Xforce dump pipes, in good condition. $300

2x RB25 AFM's, one has the filter bolt flange face cut off to allow a filter to be clamped straight on. $50 The other comes with the plug and has a test sticker on it. $75

1x CAT forward equal length pipe. Have to check brand and get pic. Off 33 gtr $300

1x NA R32 RB25, was a good running motor that I took out a couple of years ago. I have stolen a few bits and pieces, still has clutch and flywheel attached. Needs welch plugs changed but should run sweet again if refitted to a car. Pickup or delivery locally only. $200 (+ fuel if I deliver)

I'm Going high mount single so might be prepared to swap a complete twin kit for a complete single kit for RB26. These turbos for sale are off my car that was driving sweet only one week ago until it broke a ring land :-(. A full install kit for them could be supplied if needed.

I havent decided on a replacement single yet but was thinking t04z or similar 600-700hp would be the goal.

Located in Campbelltown, NSW.

PM if you have any questions.

post-15046-0-76682100-1308054957_thumb.jpg

post-15046-0-77550200-1308054986_thumb.jpg

post-15046-0-94358500-1308055018_thumb.jpg

post-15046-0-93468800-1308055035_thumb.jpg

post-15046-0-08018900-1308055083_thumb.jpg

post-15046-0-57831100-1308055101_thumb.jpg

post-15046-0-25753600-1308055120_thumb.jpg

post-15046-0-45949300-1308055153_thumb.jpg

post-15046-0-18220400-1308055187_thumb.jpg

post-15046-0-82071800-1308055213_thumb.jpg

Link to comment
Share on other sites
Dabro Collaborator

Dabro

Posted
  • Author
Posted

Hi All,

Going big single and having tidy up.

2x 2860-7 Turbos done about 15k. $2000

4x CAS units, one has the drive sleeve taken off. $75 each

2x Lower OEM R33 GTR intercooler pipes with protective cover $50 for both.

2x Xforce dump pipes, in good condition. $300

2x RB25 AFM's, one has the filter bolt flange face cut off to allow a filter to be clamped straight on. $50 The other comes with the plug and has a test sticker on it. $75

1x CAT forward equal length pipe. Have to check brand and get pic. Off 33 gtr $300

1x NA R32 RB25, was a good running motor that I took out a couple of years ago. I have stolen a few bits and pieces, still has clutch and flywheel attached. Needs welch plugs changed but should run sweet again if refitted to a car. Pickup or delivery locally only. $200 (+ fuel if I deliver)

I'm Going high mount single so might be prepared to swap a complete twin kit for a complete single kit for RB26. These turbos for sale are off my car that was driving sweet only one week ago until it broke a ring land :-(. A full install kit for them could be supplied if needed.

I havent decided on a replacement single yet but was thinking t04z or similar 600-700hp would be the goal.

Located in Campbelltown, NSW.

PM if you have any questions.

More pics of turbo

post-15046-0-12430900-1309003781_thumb.jpg

post-15046-0-35544900-1309003823_thumb.jpg

post-15046-0-41880300-1309003851_thumb.jpg

post-15046-0-36783000-1309003875_thumb.jpg

post-15046-0-32535000-1309003902_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • rbs30
      RB gearbox options

      By rbs30 · Posted

      Newcastle NSW
    • ck_chino
      Nismo copper mix twin “pull” pedal height engagement

      By ck_chino · Posted

      Installed  Nismo coppermix twin competition spec last year in my bnr32 with pull trans with Oem slave cylinder. The point at where the clutch disengages/enages is right at the top of the clutch pedal, meaning I barely have to push the pedal down for the clutch to be disengaged.  You guys that have the same combo are you experiencing this high pedal bite point??   Secondly I’d like to have the disengagement point lower meaning I have to push the pedal more(further not effort)for it to be disengaged.  I’m thinking to use a Nismo big operating cylinder(bigger bore at 13/16 vs Oem 3/4) which will require more pedal stroke to get the equivalent movement at the clutch fork. But I see Nismo web site says not to mix these 2 as the Nismo big operating cylinder doesn’t have enough stroke to disengage??? Any folks run both the coppermix twin pull with Nismo cylinder??    Thanks in advance for the replies but prefer only guys with pull clutches to respond. thanks     
    • Watermouse
      RB gearbox options

      By Watermouse · Posted

      Any chance u could let us know where your based ?
    • rbs30
      RB gearbox options

      By rbs30 · Posted

      That’s a great deal and I would jump on it if you were closer. Melbourne is a bit of a hike for me though unfortunately 
    • soviet_merlin
      Fake ARP bolts?

      By soviet_merlin · Posted

      I wonder if there is much to tell without knowing where the bolts where bought from. If it comes from Amazon or similar all bets are off. Can't trust them. And I fear not everybody knows that. Wasn't it @TurboTapin who ended up with the fake fuel lines recently? The submersible ones which very much weren't submersible at all. It kind of applies to everything nowadays. Doesn't matter if it's hardware or electronics. The fancy camera might have internals swapped out for cheap knockoffs. The hard drive will report a certain size but not actually be able to write it all. Shit like that. A bit depressing but the reality is you really have to be weary of where and how you buy stuff
×
×
  • Create New...