Jump to content
SAU Community

Recommended Posts

Hi everyone

Car is R33 gts-t S2

Issue I am getting could almost be explained like having a slipping clutch. Put the foot down and the motor will rev and suck a lot of air but it goes no where. It will get a power kick for a second then nothing then kick in then nothing. It also seems to vary depending fuel in the tank. Generally less fuel means the problem is bigger and happens more.

I have tried with no success

- New fuel filter

- Octane boost \ engine cleaner stuff

- Check coil packs for cracks

- I think i have replaced the spark plugs

Another issue I have would be the battery doesnt seem to hold charge for long. For example I didnt drive it for a week and the battery was flat. (I have no alarm) My blinker blinks fast but all lights work. If listened to the radio for an hour I believe the battery would already be flat. (only 2 standard back shelf speakers)

- I have gone through 2 batteries already

Thanks for the help all :D

Edited by Julzillionaire
Link to comment
https://www.sau.com.au/forums/topic/368290-help-me-power-loss-issue/
Share on other sites

so the revs increase but the speed doesn't? if so, definitely a clutch slip issue. a new clutch is your only real solution, but if it has been going on for a while then the flywheel might be in bad shape too. if it isn't a case of revs increasing but speed not, then your clutch is ok. if it is just that the car is gutless then it may be a fuel pump issue. if it sounds like it's misfiring, then it will be the coils, or possibly the ignitor pack (if you've changed the spark plugs then you can rule them out).

as for the battery issue, could be 1 of 2 things. 1: something is continuing to draw charge (possibly something like a boot light). this can be checked with a multimeter. 2: the alternator is cactus. again, can be checked with a multimeter.

so the revs increase but the speed doesn't? if so, definitely a clutch slip issue. a new clutch is your only real solution, but if it has been going on for a while then the flywheel might be in bad shape too. if it isn't a case of revs increasing but speed not, then your clutch is ok. if it is just that the car is gutless then it may be a fuel pump issue. if it sounds like it's misfiring, then it will be the coils, or possibly the ignitor pack (if you've changed the spark plugs then you can rule them out).

as for the battery issue, could be 1 of 2 things. 1: something is continuing to draw charge (possibly something like a boot light). this can be checked with a multimeter. 2: the alternator is cactus. again, can be checked with a multimeter.

Hi,

Speed does increase but its gutless. I'm thinking fuel as well. Thanks for the multimeter tip, I will try that.

What boost controller? Have you set it right? My old car with a profec b spec 2 would punch then hit the limiter then I lose boost and it goes gutless then kicks back in. Chucked it on the dyno and my boost graph was a f**king heart beat readout, up and down.

Stock turbo has a 7psi actuator. Switch your boost controller off and see how it runs on 7psi. Leave wastegate connected obviously just use a direct line to the inlet on the wastegate and 7psi will push it open.

What boost controller? Have you set it right? My old car with a profec b spec 2 would punch then hit the limiter then I lose boost and it goes gutless then kicks back in. Chucked it on the dyno and my boost graph was a f**king heart beat readout, up and down.

Stock turbo has a 7psi actuator. Switch your boost controller off and see how it runs on 7psi. Leave wastegate connected obviously just use a direct line to the inlet on the wastegate and 7psi will push it open.

I have forgotten all the terminology and names for things since it has been years since I was into cars. But mine has a manual boost thingy that gives it 10 psi all the time. As stock i think has 5psi then opens to 7psi ?

Do you suggest to plug it into the stock solinoid..?

your fuel pump could possibly be on its way out..

I'm thinking this may be the case. What should I replace it with? With possible upgrades in the distant future. Or where can I pick up a second hand or cheap stock one? Also do I just need a pump its self or are other items needed ?

Is this a good replacement?

http://www.ebay.com.au/itm/Walbro-GSS342-Fuel-Pump-Nissan-S13-S14-S15-R32-R33-R34-/170583647922?pt=AU_Car_Parts_Accessories&hash=item27b793e6b2

*NOTE this gutless issue has been like this over a year. Also chews through the juice compared to when I first got it. From memory

Edited by Julzillionaire

Any idea on Nissan genuine part price or even part number?

Just because there pretty quick with delivery. Usually next day.

Or even a

http://www.ebay.com.au/itm/genuine-not-cheap-copy-BOSCH-040-600hp-fuel-pump-/360191720253?pt=AU_Car_Parts_Accessories&hash=item53dd197b3d

??

Edited by Julzillionaire

the walbro would fit on the bracket better than the bosch. i've had both and the walbro fits better.

Ok Thanks for the help.

I rang bursons today and they quoted = approx $290

Repco said theyll ring back and when I rang them back said they have no idea and theres only 2 staff in the shop = approx fail

Ebay = approx $120

ebay for the win

For people in the future reading this I will be following these instructions with this fuel pump Walbro GSS342

http://www.skylinesaustralia.com/forums/topic/85375-r33-gtst-fuel-pump-install/page__st__20

So any questions PM me

I also did as much as I could out of this DIY

http://www.skylinesaustralia.com/forums/topic/174735-fixing-idlestarting-problems-rb25det-cleaning-air-regulator-easy-way/page__p__3204938__hl__tighten+throttle__fromsearch__1#entry3204938

My car idols a lot better and seems to have more guts. But now im starting to think its a clutch issue. Because its acting like when my last clutch went. Now I have to decide whether its cluth or fuel now....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've done a few BMS systems. Code in Canada use to force us to have any safety components outside of the PLC but with a code change back in 2018 I believe it was, we can now use safety PLC's to control everything. Sadly to your point, AB Guardlogix safety instructions for example are only available in ladder.  Machine safety is a very big thing here though, you're constantly forced to migrate to the next best thing by OSHA. I honestly prefer safety plc's, including anything from AB more then I do working with old school safety monitoring relays. PLC is only one portion of it, the rest of the electrical still has to follow to meet SIL (Mechanically linked dual contacts, bla bla)  Now tell me how to feel about safety over comm's (e.g Ethernet/IP CIP) on a unmaintained network haha
    • To your point, boolean logic. We're not only working with bools in ecu's, so it's very limiting. I wanted to setup a low WMI pressure alarm. After 1 second I want WMI line to hit 100PSI, 2 seconds 175PSI, etc. and trigger an alarm if it doesn't meet those thresholds. This would of taken me one very short line of text, but instead I had to bugger around with generic timers, conditions, etc. and so forth.
    • I much prefer that to an actual oil pressure issue, never would of thought it would of been a volt drop issue but SAU brains win again. Guess ill be turning down the oil pressure limit for the track and hunting some grounds. Ill hopefully update this thread with some high oil pressure and solid ecu voltage logs. 
    • You've just discovered a really good reason to tell yourself, yes, I do need to buy an aftermarket ECU. Put the MAF in the bin. Slap in the new ECU and have a think about what turbo sounds you prefer.  Do you want a 90's style BOV wooosh? Do you want a hektik tsututututu?  Mate, can't go wrong. Just gotta get that ECU and the world is your oyster. 
    • Hi. Iam just curisou about this topic. I saw this video. It is about Greddy Type FV2. I know that BoVs are about that sound but how and when to use it? I read some topic here and from what i have understand on stock RB with MAF there will be some "problems" if you use this BoV? It vents the air in to the atmosphere and the MAF on stock car needs this air back in to the intake and not out? Or is it wrong? If so...i saw you can put some adaptor to circule air back...but does that not "loose" that sound? I saw another BoV from Turbosmart and it has two "exhaust" like ports? One is for the stock tubing for letting air back and one is for "sound" and let the air in the atmosphere? Can someone please explain? This is the Greddy one:  And this is the Turbosmart.     THANK YOU!! EDIT: So i read about this topic some more and i if i understand that correctly: That Greddy can function either like BoV or 100% Bypass valve? And that Turbosmart is what they called hybrid so you can adjust what and how many air can be vented out or back in? Is this right? THX!
×
×
  • Create New...