Jump to content
SAU Community

Recommended Posts

Hey guys,

I have done a bit of a search and can't find any thing that helps.

I have just had my rb30 crank machined and a crank collar put on. I just test fitted the oil pump gear on the collar and noticed there seems to be a lot more clearance than what I would have expected. I measured a total of 12 thou, Ie 6 though on each flat face. Firstly is that normal? that amount of slop I would have expected to negate the whole purpose of the collar.

Do people shim up there gears? I'm think about getting 2 small peices 4 thou shim and loctite 406'ing it to the crank collar just to tighten it up a little. I noticed tonight that the glue added about 1 thou. so In theory it would bring it down to about 2 thou.

What does every 1 else do?

Lastly when using a standard rb25 pump on a built rb30, do people put say a 2mm washer in the oil relief valve?

regards

Chris

Link to comment
https://www.sau.com.au/forums/topic/368570-crank-collar-clearance-issue/
Share on other sites

Chris, that is why I'm a fan of welding the snout up and machining to suit the particular gears you are using. For me, 12thou is way too much slop!

As for the oil pump relief, I'm running a stock RB30E pump on my next engine and I shimmed the relief spring with an approx. 2mm washer.

Hey Mr Bubs, In hind sight I think your onto something and I probably should have gone the welded route.

12 thou makes the oil pump gear rock back and forth like its on a rocking chair. I don't understand why there isn't alot more post's relating to this subject I mean its so damn obvious to me lol

Yeh that point is a good one. However, What does the clearance become when the engine is running and everything has heated up and expanded?

Also another point is the crank doesnt run perfectly centred at xxxx rpm, there is always a certain amount of runout. Too tight on that clearance and it will be just as bad as not having a collar at all. How much runout there is i dont know, But there is no way the snout is always perfectly centred when your at 7000rpm bouncing off the limiter.

But 0.012" is alot, and no doubt it can probably be run abit tighter. But there is no way of knowing until someone who has run tighter can say its been fine and tells you what clearance they actually did run. Or you try it yourself and see what happens.

But I dont think 0.002" is enough. Hopefully someone else with more exp can shed some light here.

If I was going to machine a collar Id probably aim for about 0.006" overall, 0.003" per side. But thats just my own guess. Without knowing expansion and run out its hard to say.

Yeh that point is a good one. However, What does the clearance become when the engine is running and everything has heated up and expanded?

If both pieces are made from the same metal (or if they have the same coefficient of thermal expansion), the clearance will not change if they stay at the same temperature.

Chris, that is why I'm a fan of welding the snout up and machining to suit the particular gears you are using. For me, 12thou is way too much slop!

how hard did this hit the back pocket? significantly more than collar?

Doesnt the aftermarket crank collars and a std r33/r34 crank measure up the same OD?

I think you might be right but I no longer have the neo Rb25 block to mic it up. I went with the 4thou shim and its still possible a bit tight. I'll have more of a look tonight now that the glue has dried and I can take the sharp edges off the shim.

how hard did this hit the back pocket? significantly more than collar?

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

is you mates motor rb26 or rb30?

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

Whats the 2J setup look like exactly? How many splines and do you know what sort of clearance it runs? No doubt its better then our nissan design. Seems toyota also improves on everything nissan didnt :( Splined from the get go sounds alot better.

Im guessing it probably has ample clearance as well, or maybe their cranks are made of better material and dont flex/runout as much?

is you mates motor rb26 or rb30?

25t/30

We had it done to my mates 30

:thumbsup:

Whats the 2J setup look like exactly? How many splines and do you know what sort of clearance it runs? No doubt its better then our nissan design. Seems toyota also improves on everything nissan didnt :( Splined from the get go sounds alot better.

Im guessing it probably has ample clearance as well, or maybe their cranks are made of better material and dont flex/runout as much?

It looks pretty much like an axle end where it goes into the diff.. as for clearance, I have no idea. Shanef was working on a splined setup for RB's but got ripped off by his machinist or something :/

2JZ-GE oil pump..

oilpump.jpg

Hey so it turns out that 4tho shim is still too tight and I can't get the oil pump gear on. which is a pain when I know that if the gear is in position I can push 2x 6 tho feeler gauges under it.

Also Loctite 406 is not a valid option as it is extremely hard to get it to key on and stop the shim from peeling off. Thats If you are quick enough to actualy get the glue on without gluing the shim to your hand first.

My boss suggested using Loctite 680 high strength retaining compound. So I'll let you know I go with that experiment.

At the rate I'm going this motor is going to take about 2 years to get running. Almost give you a run for your money ay Bubba????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...