Jump to content
SAU Community

Rollcages

*ALL-DAY*

By *ALL-DAY*,
in Fabrication

 Share

Recommended Posts

MBS206 Grand Master

MBS206

Posted
Posted

You can get them passed by CAMS for a cage built by anyone, but in doing so, you do need to have all of the correct material purchased etc. It's not just any old tube that will do.

They also need to be built to the correct design.

Link to comment
https://www.sau.com.au/forums/topic/368713-rollcages/#findComment-5879735
Share on other sites
Risking Grand Master

Risking

Posted
Posted

It can be built yourself and certified by CAMS that's no problem.

Expect to be asked for an invoice for the material you used as proof and possibly an MDS (material data sheet) if you get a strict scruitener to inspect it.

They will check for 360 degree welding, base plate dimensions and fixings, bend radius' and intersection locations.

As well as shedule compliance and category requirements.

All the regulations are in the online cams manual under shedule J.

Be warned though if it's not 100% chances are it won't get approved and the expense to cut it out and do it properly

is alot more than paying someone to do it right the first time around.

It's not hard if your competent with a welder and have access to the right equipement

Link to comment
https://www.sau.com.au/forums/topic/368713-rollcages/#findComment-5880861
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • r32-25t
      2025 Osaka Auto Messe

      By r32-25t · Posted

      I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to come I’ve seen though 
    • Rezz
      2025 Osaka Auto Messe

      By Rezz · Posted

      $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Dose Pipe Sutututu
      R32gtr sputtering and stalling

      By Dose Pipe Sutututu · Posted

      Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • joshuaho96
      R32gtr sputtering and stalling

      By joshuaho96 · Posted

      I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...