Jump to content
SAU Community

Recommended Posts

And yes I have done searches on previous threads & from that I have Questions I hope you guys can help me with or put me in touch with people who have done this. Ok my car 1998 S1. Doner car is a 2000 model RS4 S2 correct me if Iam wrong R33GTR box? Push or pull?

This is a list of parts I think I need as sourced through searches.

1. Do i need the flywheel & bolts off doner manual car or will the auto one ok? (knowledge on flywheels/transmitions limited as you can see)

2. Clutch pressure plate & bolts.

3. Spigot bush

4. Bellhousing bolts. (I think there longer in the manual)

5. Clutch master & Slave.

6. Clutch piping line

7. Clutch & Brake pedals with mounting bracket & bolts

8. Handbrake lever, mounting bracket, cable & bolts

9. CTR console

Please add to my shopping list if I have missed anything. Any help will be appreciated.

If I go ahead with project any volunteers to assist will be rewarded handsomely (Free Beer-Food)Ha! Ha!I'm in the Newcastle area. NSW

Thanks again Shane

Is your donor car a factory manual (RS4-S) or is it an auto that was converted? If it's an RS4-S the gearbox will be pull type.

You should be able to use the flywheel from the donor car without any problems.

I dont know whether the flywheel bolts differ from auto or manual, but I would be going brand new ones from nissan anyway, rather than reusing old ones.

As for your other parts, looks like you have most of it covered. You will also need the manual footrest, and the rubber boots around the gear shifter.

I'm going to be doing the conversion very soon, here is my parts list if you want to look at it

Manualconversionpartslist.pdf

you dont have a flywheel in your stagea at the moment you have a drive plate/flex plate with a torque convertor bolted to it. you will need the flywheel as stated above. i would also say you need the flywheel bolts to suit given that the flywheel will be much thicker than the plate that comes off. not sure but possibly the gearbox mount and tailshaft are different?

Thanks Taylor... When it comes to gearboxes i'm like a fish out of water. Hopefully after this conversion my knowledge on them will improve...I think i'm ok with using the auto Tailshafts & mounts as I found in a search done previous

Cheers Brian,yes it is a factory manual. So is the factory a R33 or R32? If you don't mind me asking how much was your new clutch, spigot bush & gasket set?

I dont know whether the RS4-S is an R33 GTR or a GTS-4 gearbox, or if there is even a difference between the two. It's definitely not an R32 item though.

I cant remember the exact price off the top of my head at the moment, I bought the seal kit and clutch from www,kudosmotorsports.com, as well as a couple of other bits and pieces.

Remember that push type clutches are cheaper than pull type though, so you will probably have to pay a little bit more for whatever clutch you choose

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...