Jump to content
SAU Community

Recommended Posts

hey there guys. got defected for being to low the other day and need to get a roadworth. before i went to take it in i gave it and the engine bay a wash. i then backed it out of the wash area and into the garage. about 10 minutes later i went to take it for a drive and it had a miss at idle. i went to keep driving it as i was heading to a workshop anyway only to have the car almost die when i went to drive off. and didnt improve at all down my drive. so i took the car back to the house. its a series 1 r33 gts with the only engine mod being a k&n pannel filter. any suggestions on what the problem might be. thanks

Link to comment
https://www.sau.com.au/forums/topic/369131-r33-gts-missfire/
Share on other sites

Depends on what the problem is. If it is a missfire as in the a cylinder is missing a spark and causes the engine to make a noticeable jump then your coilpacks need to be replaced. This is likely as your coilpacks are pretty sensitive (shock, moisture). Also depends what else you got wet and how the engine is behaving so try and give us some more details.

the car runs great first thing when the engine is cold. as it starts to warm up it starts missing at low revs. the hotter the engine get the worse it gets at higher revs. so when it first starts to warm up the car runs well when travelling at 2500 rpm but almost stalls at idle. then when at operating temperature the car misses badly at revs and only slightly at idle. will be checking coils.and plugs this morning

It'll get better over time but it'll wear the f**k out of your engine.

Pull every spark plug out, dry out each plug/where it plugs into.

Make sure none of them are f**ked. You may want to grab a piece of fine-grit sand paper and clean up the sparking parts of the spark plugs.

Then, you need to get in your car, drive down to the local mechanic, tell him what you did and let him fix it.

Running worst when warm reminds me of my coilpack issue... i covered it in silicon however I'd recommend you leave that resort till last. You want to attack the immediate problem as opposed to imminent problems.

But yeah tbh I wouldn't even bother touching the car myself.. your mechanic will have all the replacement parts and knowledge you need to fix this.

Edited by SKITTLES

geez i really cant remember the voltages but if you had a power fc it would tell you automatically. There's a few posts that explain which terminals are which and what the correct volatges are. Not too sure if you should bother with this one, basically the car wont be able to hold idle and will just die if the afm is ruined.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...