Jump to content
SAU Community

Recommended Posts

After blowing the engine of the R35 into 4,823,163 pieces (Yes I counted) I decided to get my local mechanic to fit the engine rather than doing the sensible thing and send it to Martin at Willal.

WELL on opening up the lines etc there are pieces of engine in the oil cooler, in the filter in all the oil lines we even found a gudgeon pin in the throttle body.

We are going to flush everything out but how can we be sure that there is no shrapnel left in the circulatory system of the car.

Link to comment
https://www.sau.com.au/forums/topic/369242-r35-engine-replacement-problem/
Share on other sites

:O

There's probably no easy way to do that, other than manually disassembling all connections and peering into / flushing them. Assuming fluid can sufficiently pass through the circulatory systems when you flush them, they should be safe. Worst case scenario something dislodges down the track and blocks up the works, but shouldn't cause instantaneous catastrophic damage unlike things trapped in the intake.

The intake and breather side of things is, at the least, what I'd be pulling apart piece by piece and either replacing or making sure they are free of shrapnel. Anything that can make its way into the throttle body etc.

Metal detector / stud finder might be of use?

replace the oil cooler cores. too many fine passages in there and just too big a risk to flush and hope for the best after a catastrophic blow up. remove and flush all the oil system lines and even the cooling system (un-usual for stuff to get into the coolant circuit though). as far as inlet goes I'm sure head has been replaced/rebuilt so just need to remove the inlet and exhaust manifolds and clean them out properly.

I guess I'll be the first to ask....

how did it happen?

F....d if I know!

Just driving through turn 9 (The one after Corporate Hill) at Eastern Creek when I heard a huge bang.

I thought it was a tyre blow out until the car came to a slow halt leaving bits and pieces of car across 800 metres of track

If you are concerned even after flushing and pulling stuff apart consider mesh filters in various supply lines to the engine (coolant/oil etc etc) after putting back together. Similar to the ones used in dry sump setups.

F....d if I know!

Just driving through turn 9 (The one after Corporate Hill) at Eastern Creek when I heard a huge bang.

I thought it was a tyre blow out until the car came to a slow halt leaving bits and pieces of car across 800 metres of track

warranty? or was it mod'd?

After blowing the engine of the R35 into 4,823,163 pieces (Yes I counted) I decided to get my local mechanic to fit the engine rather than doing the sensible thing and send it to Martin at Willal.

WELL on opening up the lines etc there are pieces of engine in the oil cooler, in the filter in all the oil lines we even found a gudgeon pin in the throttle body.

We are going to flush everything out but how can we be sure that there is no shrapnel left in the circulatory system of the car.

SURE = 100%. You cannot be sure. Apart from replacing the entire system.

But you can be reasonably sure. Flush lines and components with solvents, look at the outflow.

Throw stuff that has small gaps (e.g. oil coolers), hope for the best.

Cheers,

SW

  • 4 weeks later...
  • 2 weeks later...
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • $53.35 and a double din Pioneer head unit that I have...
    • Put a camera facing your dashboard so you can film the gauges. Head out to a straight but of road, and filming it as you go from a stand still at wide open throttle to as fast as you can/feel comfortable doing. Then film the dash board as you for example accelerate like normal onto a freeway. This will give us an indicator from Speedo of your expectation of slow, and will give us the rpm reading too to see if it's shifting. (Auto still has tacho from memory)
    • Buy yourself the cooling system pressure tester. Being able to pump it up, and have a gauge on it, AND have a cold engine makes it much easier / practical to diagnose. Additionally as the engine isn't running, you can listen for pin hole leaks as well as watching if pressure drops away. In addition, you can pressurise and while doing so, watch all the little rubber hoses. Some fail very brittle, and will just leak, while others can end up very soft and bulge. While a bulging hose isn't necessarily leaking, one of those small ones starting to stretch / expand in a bad way is an indicator that you'll be looking to replace that one soon   Depending on if this is a project car, or you'll be dailying it in the summer months would alter how I'd be most comfortable with driving the car and how I'd replace. If you're planning to use it as a daily, with no backup, I'd pull the engine, and replace all the external oil/water lines in one big swoop. At the same time do the timing belt, water pump, tensioners etc. Do not open the engine at all. We just want to replace all the things that are inexpensive as a single item, but a PITA when they go. By doing the above, you've made the car from a bunch of age related issues more reliable. If it's a project, and you like swearing while trying to reach into dirty hard to reach places to replace a single hose that may or may not be the leaky one. Just replace the leaking/bad ones as they need it. If it's a project and you'd rather swear at the car once and enjoy it as much as possible, then refer to the process I mentioned in how I'd want to do it if it were a daily. However, the approaches above do come down to how much spare pocket change you have. Pulling the engine and dropping over a thousand dollars on parts, may not be practical for you. Oh, if engine outing, I'd replace as many silicon/rubber inlet joiners as possible too.
    • Yeah, they're pretty dumb though...ie; they'll throw a solenoid error if the solenoid is dead, shorted, wiring is open circuit, or even if the driver transistor has failed (they can't self-diagnose much, they can only test inputs/outputs)... but if you wanted to try, I believe it's this protocol....(uses a long pulse indicator with short pulse counter)...    
    • Yeah I'll do what I can without taking off any major parts for now. If it becomes clear I won't get far with the engine in the car I'll have to think about the next steps. I am not too stuck on keeping everything 100% OEM, if there is better solutions, like converting most lines to braided with AN adapters, I'd rather do that than buy overpriced new "shit" parts.
×
×
  • Create New...