Jump to content
SAU Community

R35 Engine Replacement Problem

Dominic

By Dominic,
in R35 GTR

 Share

Recommended Posts

Dominic Rising Star

Dominic

Posted
Posted

After blowing the engine of the R35 into 4,823,163 pieces (Yes I counted) I decided to get my local mechanic to fit the engine rather than doing the sensible thing and send it to Martin at Willal.

WELL on opening up the lines etc there are pieces of engine in the oil cooler, in the filter in all the oil lines we even found a gudgeon pin in the throttle body.

We are going to flush everything out but how can we be sure that there is no shrapnel left in the circulatory system of the car.

Link to comment
https://www.sau.com.au/forums/topic/369242-r35-engine-replacement-problem/
Share on other sites
Birds Grand Master

Birds

Posted
Posted

:O

There's probably no easy way to do that, other than manually disassembling all connections and peering into / flushing them. Assuming fluid can sufficiently pass through the circulatory systems when you flush them, they should be safe. Worst case scenario something dislodges down the track and blocks up the works, but shouldn't cause instantaneous catastrophic damage unlike things trapped in the intake.

The intake and breather side of things is, at the least, what I'd be pulling apart piece by piece and either replacing or making sure they are free of shrapnel. Anything that can make its way into the throttle body etc.

Metal detector / stud finder might be of use?

Beer Baron Grand Master

Beer Baron

Posted
Posted

replace the oil cooler cores. too many fine passages in there and just too big a risk to flush and hope for the best after a catastrophic blow up. remove and flush all the oil system lines and even the cooling system (un-usual for stuff to get into the coolant circuit though). as far as inlet goes I'm sure head has been replaced/rebuilt so just need to remove the inlet and exhaust manifolds and clean them out properly.

Dominic Rising Star

Dominic

Posted
  • Author
Posted

I guess I'll be the first to ask....

how did it happen?

F....d if I know!

Just driving through turn 9 (The one after Corporate Hill) at Eastern Creek when I heard a huge bang.

I thought it was a tyre blow out until the car came to a slow halt leaving bits and pieces of car across 800 metres of track

Ant97GTR Grand Master

Ant97GTR

Posted
Posted

If you are concerned even after flushing and pulling stuff apart consider mesh filters in various supply lines to the engine (coolant/oil etc etc) after putting back together. Similar to the ones used in dry sump setups.

domino_z Mentor

domino_z

Posted
Posted

F....d if I know!

Just driving through turn 9 (The one after Corporate Hill) at Eastern Creek when I heard a huge bang.

I thought it was a tyre blow out until the car came to a slow halt leaving bits and pieces of car across 800 metres of track

warranty? or was it mod'd?

saliya Rising Star

saliya

Posted
Posted

After blowing the engine of the R35 into 4,823,163 pieces (Yes I counted) I decided to get my local mechanic to fit the engine rather than doing the sensible thing and send it to Martin at Willal.

WELL on opening up the lines etc there are pieces of engine in the oil cooler, in the filter in all the oil lines we even found a gudgeon pin in the throttle body.

We are going to flush everything out but how can we be sure that there is no shrapnel left in the circulatory system of the car.

SURE = 100%. You cannot be sure. Apart from replacing the entire system.

But you can be reasonably sure. Flush lines and components with solvents, look at the outflow.

Throw stuff that has small gaps (e.g. oil coolers), hope for the best.

Cheers,

SW

  • 4 weeks later...
  • 2 weeks later...
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • GTSBoy
      AC not coming from top vents

      By GTSBoy · Posted

      What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • dbm7
      Shifting questions

      By dbm7 · Posted

      ...oops. forgot the TCU end...
    • Sleepergm
      Custom titanium intake

      By Sleepergm · Posted

      No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...