Jump to content
SAU Community

Recommended Posts

Hi All,

We have just started up a N/A car club for Sydney owner we have set down a meet up which will be as listed below:

Meet will be @ Sydney Olympic Park on 11 July 2011

to RSVP please text 0438870091 with your name and your car

Meet will start at 7pm, If you feel the need to do skids DON'T COME

Please refer to Club rules on "Info Page"

IRRESPONSIBLE BEHAVIOR WILL NOT BE TOLERATED

Members who do not RSVP will NOT be accepted!

Show your N/A spirit and turn up! please note all attendees must RSVP.

PS you can find out Facebook page @ http://www.facebook.com/pages/Sydney...31677050182943

Is this only for n/a or can anyone come as Sydney olympic park is just down the road from me

Looks like it's only for n/a's so pretty much the cruise will be ruled by p platers who would prob just hoon.. Don't think it'll be worth risking a defect for.

Looks like it's only for n/a's so pretty much the cruise will be ruled by p platers who would prob just hoon.. Don't think it'll be worth risking a defect for.

True that, not going to assume they'll all hoon but a big group of p players in JDM cars is definatley going to get pulled over I might aswell drive me car to the cop shop and pop my bonnet,

it will amount to te same thing

Looks like it's only for n/a's so pretty much the cruise will be ruled by p platers who would prob just hoon.. Don't think it'll be worth risking a defect for.

Yes you are correct this is only for N/A cars, No "hooning" will be done as stated on the page we are very strict with this and will ban any member caught engaging in any of these activities.

Give the guys a break, they are just trying to appreciate their cars like we do.

And at least they are trying to follow the rules, unlike the countless p plates I keep seeing on turbos and v8s



  • Similar Content

  • Latest Posts

    • Hard to find reliable dyno results that help my selection   Thinking G30- 660 twin scroll 1.06   Problem is my current setup isn't imo terrible. This is the genuine flog it at the track tune so there is a few kws in it but pulled for track safety   Non VCT RB25DE home built and has baby 256 Poncams, 60mm throttle body. 90mm exhaust and decent ARC cooler with Emtron KV8 Would like to break 400rwkws on 20psi and want a bit more through the 4,000rpm range. New setup needs to beat attached dyno
    • Hey y'all, had some bad ball joints in my tie rods, so figured i'd just replace both inners and outers.  Went with the high-misalignment system from GKTech. My car's lowered so figured why not. M14 Super Adjustable Inner Tie Rod High misalignment S13 240sx/S14/S15/Skyline tie rod ends (12mm/14mm) Welp, took over a week to get the job done, but finally did. Took it on the maiden voyage today and... - The OE boots do not sit properly on the new inner tie rods - If you look at the photo in the link above, new ITRs are basically threaded all the way through the length of them, so best I could do was tighten the boot down with a screw-down hose clamp onto the ITR's threads. - There is a "whoosh"ing sound every time I turn the steering, seems like it could be coming from the air moving into/out of boots. Concerning, bc it'll likely pull in nasty shit from the outside when I turn... namely thinking of moisture. - Looking at the rack from the back of the car, under it, the left tie rod is straighter than the right. Right droops down a bit. - My alignment is way outta wack, that's expected. Taking it to get an alignment as soon as I can. - The big thing is that the steering isn't really "springing" back like it used to. Wondering if there's something tied to pressurization of the system that I managed to f**k up. This was supposed to be a 20 min job... why doesn't anything ever go right with these cars?
    • Thanks guys, toruqed down to 65ft-lb, or 88 n-m.  Now have other problems, will chronicle in another thread. You guys are the best, thanks for all the ugga duggas.
    • R serious becoming more of a weekend cars or collectors cars there are less on the road these days , but you sometimes come by one or two . we might have to start spotting the V serious to make up for the gap.  
×
×
  • Create New...