Jump to content
SAU Community

Recommended Posts

im about to get my power fc tonight was wondering what the std preset settings aer like on the power fc. my car is std boost with fmic, pod filter and exhaust. am i really just able to plug it in and drive off, im scared something will happen like it wont work or car will drive weird. anyone with experience can help me out???

Link to comment
https://www.sau.com.au/forums/topic/36998-wats-std-power-fc-settings-like/
Share on other sites

i got my pfc last week and put it in the car around 30 minutes and drove away. The car is dream now to drive. Now the boost is strong and hard and you will manage to pull away from a lot of cars. Yeh you can drive it around no problems until you get it tunned. Just dont boost the crap out of it without knowing your limits. Nothing weird should happen unless you got your boost controller setting turned on which will stop you from starting the car.

hope this info helps

Ak

im about to get my power fc tonight was wondering what the std preset settings aer like on the power fc. my car is std boost with fmic, pod filter and exhaust. am i really just able to plug it in and drive off, im scared something will happen like it wont work or car will drive weird. anyone with experience can help me out???
Yes the default settings are fine for your car.  

If the car doesn't start make sure you have the Boost Controller option off .

Crap

Settings are fine for your car if you run 100 RON and are in (lower) Japan ambient temperatures.

Both my S15 and GTR pinged with the PFC factory settings in summer with less than a moderate boost (less than 1 bar).

Suggest tuning ASAP for the sake of engine insurance.

Crap

Settings are fine for your car if you run 100 RON and are in (lower) Japan ambient temperatures.

Both my S15 and GTR pinged with the PFC factory settings in summer with less than a moderate boost (less than 1 bar).

Suggest tuning ASAP for the sake of engine insurance.

Crap,

did you notice he said standard boost? I drove mine hard on hot summers days with out getting it tuned no probs - with standard boost. When it did go on the dyno, it was rich everywhere.

Yep - may have been rich, but the timing is quite advanced through the meat of the torque curve.

I've damaged two engines by driving them on PFC base maps - no one's fault but my own.

I can only speak for S15 and GTR units - but that's my experience and my advice. It's up to you vendetta if he wants to take it or not.

GAV- so will i be fine if i dont thrash the shit out of it. id get it tuned now but i want to wait to put a bigger fuel pump and then boost it to like 10-12. cos it will be a bit of a waste if i get it tuned now on std boost and fuel if im changing it in the near future. Gav if i just drive it like normal without punishing it until i get it tuned will i be safe or still damaging the engine

Steve- how long did you drive without getting it tuned and leaving it on standard pfc settings

If you HAVE to drive it untuned, keep the boost down and make sure the knock warning settings are turned on (same menu as the boost control kit, AFM max warning etc). If the knock warning goes off - believe it! In my experience the minimum setting (60?) is a little high and my tuner has heard knock below this.

BTW - Don't know what car you have. If it's a GTR, make sure you tune with the Datalogit as it gives a much better result (and heaps less dyno time!).

Don't think it's available for RB25 yet, however.

Anyway, good luck.

is it just a switch or do i need the hand controller to do it..do you guys have the hand controller with yours?

You need a HC to do this.

Crap

Settings are fine for your car if you run 100 RON and are in (lower) Japan ambient temperatures.

Both my S15 and GTR pinged with the PFC factory settings in summer with less than a moderate boost (less than 1 bar).

Suggest tuning ASAP for the sake of engine insurance.

PowerFC detonation sensor is set to go off above 60. For the entire duration I had the powerFC in the car before tuning I did not get above this (maybe a month or so). It was midyear then so the weather was cool and I was running 1 bar boost via removal of the boost solenoid. My car is a R33 GTR btw.

During this time I did hit full boost but did not do anything like extended power runs or track days. Gav, you speak from experience on this matter having damaged two engines but so am I. I did not get any detonation at all... seriously. When I did get the FC tuned the tuners advanced my ignition further anyway and leaned the mixtures.

GAV- so will i be fine if i dont thrash the shit out of it. id get it tuned now but i want to wait to put a bigger fuel pump and then boost it to like 10-12. cos it will be a bit of a waste if i get it tuned now on std boost and fuel if im changing it in the near future. Gav if i just drive it like normal without punishing it until i get it tuned will i be safe or still damaging the engine

Yes it would be a waste of money getting it tuned twice but then if you're worried why don't you wait for the fuel pump and then only put in the powerFC.

In my experience the minimum setting (60?) is a little high and my tuner has heard knock below this.

I think this would be debatable. This maybe the case but also on the flip side it come go above 60 and you can hear no pinging at all. The knock sensors in different cars may operate at different sensitivities due to age of car/wear/ whatever.... but I do not believe if the det sensor goes off in the PFC it means that detonation has occured. A few tuners have said this as well incl Hitman to name one.

im getting the power fc now as the price i got it for i doubt it id gdt it this cheap ever again. otherwise the power fc is the last thing id get.

When the power fc is brand new is it set to boost controll OFF std. as i dont have a HC. ???

What I meant is why don't you get it now and not put it in until you get your fuel pump. From memory the boost control is ON std but I have a bad memory :(

Boost control option will be ON by default for a new PFC.

Won't do any harm except that the engine check light will stay on.

I'm not sure if the engine check light will be able to flash in this mode, however, if you experience warnings (knock, max injectors, max AFM).

When i got my pfc and plugged it into my GTS25t it pinged its tits of.

After tuning it was fine.

If you want to see how good it runs with the base maps (with regard to pinging) set the hand controller to monitor detonation. It will log the current and the peak amount of detonation. I have been told that you can drive around with it pinging 20 all day. If you get over 60 that is the point your engine light will start flashing (if you have that option set in the pfc using the hc) and that is also the point at which i am told the pinging is audible.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I鈥檝e been super cautious, did a lot of research, and took my time. I鈥檝e driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times鈥攏o issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It鈥檚 not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test鈥攂elt isn鈥檛 too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it鈥檚 slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it鈥檚 just how it sits? I鈥檓 probably overthinking this, but since it鈥檚 my first time doing this on a NEO and the engine is forged, I really don鈥檛 want to mess anything up.   Also, I鈥檓 thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there鈥檚 a real difference between the two.   Any advice or reassurance would be much appreciated!
    • 40 grit sounds about right, to start. You make some decent cuts/damage in the coating with that, then rapdily scale up to maybe 80 and 120 for the bulk of the actual removal, then fine it off to 180 or 240 perhaps. No need to go any finer than that, and maybe no need to go even as fine as that. Wrap it on a big block and have at it. At least on the hub face.
    • Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes. Traction is going to be at a premium!
    • Hello,   My name if Frederick, i'm 30 years old and I live in Belgium, Europe! I used to have a Nissan 370z daily but since I got a company car I turned that into my seattime driftcar. About 3 years ago I also wanted something older with more feel, so I got an R32 GTST with an rb26 engine. I am now getting the rb built to have around 800hp and it's close to being finished. I'm very excited for how it will drive and how driveable it will be! Regards, Fred!
    • Appreciate the insight! Talked to some local folks and they basically told me "it's not that deep." As long as the threading on the inside matches what's at the steering rack, everything else can be constructed-to-fit. There are full aftermarket kits I can use - probably better for my car overall since it's lowered.  Example: GKTech M14 Super Adjustable Inner Tie Rod Set - Nissan Skyline R32 R33 R33, 240SX, 300ZX, 350Z / Infiniti G35 M14I-TROD-2 gktM145-TROD gktM14I-TROD - Concept Z Performance (These can be packaged with their "high misalignment" tie rod ends).
  • Create New...