Jump to content
SAU Community

Recommended Posts

Ok guys need a reliable auto electrician to come and have a look at my R33 as i think i might have damaged some electric parts when trying to jump start the car yesterday. I put the cables the wrong way (i know stupid, but hey shit happens) and had some smoke coming from inside the car dashboard. The car does not start at all, it will not even crank, all other electronics work in the car if the key is put in ignition.

So yes anyone can recommend an electrician that will not charge an arm and a leg that could come to my place and have a look at it.

Location: Merrylands

Edited by aky
Link to comment
https://www.sau.com.au/forums/topic/370475-auto-electrician/
Share on other sites

Checked the fuses in the boot, they look to be fine. I was thinking of maybe taking the fuses to supercheap and getting a new battery, then replace them all and see how it goes. But would still need an auto electrician in case that does not work.

Went to chk the fuses under the dashboard 2nit, thought to my self lets see if it turns on, surprise surprise it turned on and i took it for a little drive everything looked fine. Parked the car then tried to start it again about 30min later and it will not start, but it at least it makes clicking sounds now. So now i am thinking that it might be the battery that is dead, so will get a new battery tomorrow and will see what happens.

Bought a new battery, put in and it started without any issues. Took it for a drive all good, started the car after 30 min again and its still starting without any problems. So it looks like the battery was the problem after all, the other battery was all watery when i took it out so must have damaged it when trying to jump start it. So relived thought i might have done some serious damage to my car.

  • 4 weeks later...

Nerds lol

I had smoke come from my blinker switch today... Can't be good ay lol

Your relay/blinker might be on its way out. Smoke is never good. What is it? Unless its a fuse melting(which is very unlikely as they designed to blow, unless you put a higher rated 40a fuse in a 5a slot) it is most likely the wire casing melting. This isn't good. One second is nothing, but 3 - 5 seconds is enough to get rid of the plastic and leave bare wire exposed which can cause havoc. My mates ford laser smoked for about 3 seconds, he used the wrong fuse which didn't blow and allowed too much current through. The end result was a bundle of wire with minimal shielding literally melted together. He traded the car in the next day.

I'm pretty handy with electronics, if anyone needs help, I'm near Parramatta and can see what I can do. Ive fixed all issues both electrical and mechanical in all my cars and helped my brother rig up two of his cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...