Jump to content
SAU Community

R34 Gtt Parts Manual Box + More!

Wilkins026
 Share

Recommended Posts

Wilkins026 Community Regular

Wilkins026

Posted
Posted

Hey guys this is the stuff i have left for sale

Manual gearbox with short shifter $1650

Dashboard $100

Bonnet hinges $50

Drivers door (white) $200

Drivers front gaurd (white) $100

All seatbelts, no rips or anything make offers

All plastic trims from inside except drivers front pillar.

Front seats $100

Rear seats $50

17" wheels with near new tyres $700 sms for photos

rear quarter windows $150 each LIKE NEW

Rear Brakes and uprights $350 or whole rear end with CV's and diff $550

K-sport coilovers $400

Radio steel brackets with little glove compartment thingy $40

If anyone needs a roof or drivers rear quarter panel i can cut them off for you, Let me know?

All parts located in WINDSOR * NEW SOUTH WALES

Tim

0404321205

Link to comment
https://www.sau.com.au/forums/topic/370614-r34-gtt-parts-manual-box-more/
Share on other sites
  • 1 month later...
  • 4 months later...
  • 1 month later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      @GTSBoy Yeah i know. The RB20 has 180Nm torque and the gearbox "should" take up to 400Nm if you are not doing stuff like drag/drift or dumping clutch and of course then it is pure "luck" on how will it last. My problem is (i think i said this in different post) that my car was very badly maintain so i would not be suprised if the oil in the gearbox was not changed until i bought it. Yeah the gearbox seem little bit sad.   @Sxnjeet the +T seem very interesting but from where iam from it was nearly "impossible" to done right and not blow twice as money as just swap for the RB25.
    • Predator1
      How to preserved a signed plastic??

      By Predator1 · Posted

      Hi, I went to the MINES shop here and bought something.. Niikura-San just happened to be there so I managed to take some pics and got him to sign my dash surround thingy. Its still wrapped in plastic back home.. I was thinking how to preserve the signature??? Im sure someones thought of this and done this in the past.
    • mcfwordsworth
      Purchase new air conditioning condenser, and receiver / drier

      By mcfwordsworth · Posted

      Perfect - thanks Joshuaho96!  Will see what I can source.
    • MBS206
      Spray painting interior plastics

      By MBS206 · Posted

      If the plastic wore, the paint will wear quicker. Heck, most car manufacturers cant keep the coatings they put on their buttons/trims alive these days for more than 5 years... A cheap paint won't do it!   However, you can get away with high quality vynil wrap, primarily in areas that won't cop much abuse. Skip colour matching, and just try and wrap a specific area with an edge in a new colour.   PS vynil wrapping is a prick of a job, and I suck at it, even for a small dead flat surface...
    • MBS206
      Help Understand GTT Boost Setup

      By MBS206 · Posted

      I think this is more a question you should ask the tuner. My assumption is you have nothing plugged into the original pin for ring gear crankshaft, which is where your map sensor should get wired to, but now you've asked the tuner to disable it. I'm assuming (because I haven't memorised your setup) you are using RB25 ECU on the RB20 loom, to plug into an RB25. You will want to check what else is connected potentially backwards between the engine, loom, and ECU. You might be all fine and safe. The best solution you could have done is wire in a map sensor, and leave the ECU able to read a map sensor.
×
×
  • Create New...