Jump to content
SAU Community

Rb25/30Det

R32Abuser

By R32Abuser,
in Engines & Forced Induction

 Share

Recommended Posts

R32Abuser Mentor

R32Abuser

Posted
  • Author
Posted

Something I am curious about. From where Im standing, I believe it may be one or a combination of:

a) Cams - As Cubes stated, the R32 RB25DE head causes the motor to ping easier than normal

b) Cam timing - Possibly issue with CAS, or base timing

c) Static CR (assuming the head is approx as Bl4ck32 stated) - the 9:1 CR would make the motor more succeptable to pinging than say an 8.3:1 motor. However, I dont see this as being the issue right now until we've ruled out timing. However, I have heard two VERY different values for the head cc measurement which has caused some confusion.

One thing to note is that the tuner had dealt with a Stagea RB25 Neo with similar/same pistons. Same symptoms. Put E85 in it and it was all good and made plenty of power.

Always options to consider...

  • Replies 146
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

R32Abuser Mentor

R32Abuser

Posted
  • Author
Posted

As rolls said

207RWKW on the 7-8 deg of timing. AFR's were apparently spot on.

Been doing a few calcs here and there and all are coming back the same... Approximately 9:1 pending a few things.

The only thing I'm not 100% on is the chamber volume. Im 99% sure it is as per Bl4ck32/Cubes measurements at 62cc. That is unless there was a serious issue with the head being overheated earlier on in its life. I just cant be too sure unless I get it measured...

Anyone got any ideas on how much (an average value) they would take off a warped head to see it flat again?

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted (edited)

I would go somewhere else and get a second opinion.I dont know how the motor was built but to be tuning it for full load on a 30 minute old engine seems a little odd to me. Please correct me if its only a base tune for the run in process that they are doing.

please explain how the engines ever gonna be in better condition to handle a thrashing than a few minutes after the rings have finished bedding in? 1000km run ins are useless

as for the head, it depends how badly it was warped but normally its not enough to affect compression by any signifigant amount. i've had my head faced 3 times now (its never been cooked badly though) and i'd be lucky to have gained 0.1 compression.

Edited by JonnoHR31
Rolls Grand Master

Rolls

Posted
Posted

Yeah once the rings are bed in, change the oil and go for gold, never understood the process of running in a motor. Once you've bedded the rings and got any metal left over from the build out of the oil then what else is going to change? Nothing I hope!

R32Abuser Mentor

R32Abuser

Posted
  • Author
Posted (edited)

Again I will say it won't be an inherent problem with the the RB25DE head or cams specs.. my money is on the wrong pistons for the application.

Ive done a few investigations and by using online calculators and inputting the following:

6cc dome pistons (Confirmed many times via R33 RB30DET thread/Spool Imports)

1.28mm Head Gasket (0.05") (Cometic) (Confirmed via Spool Imports)

86.5mm Stroke x 86.5mm Bore

0 Deck height (From speaking to the builder, the deck height is actually below 0 deck height (decreasing compression!) exact value Im unsure of)

62cc combustion volume (Head type Confirmd by Cubes as being an R32 RB25DE head. Also, 4 different R32 RB25DE heads all cc'd to this value - so the only way mine may read less is if it had been seriously overheated and decked to get it straight again)

Standard pin height 1.280" (As confirmed by Spool)

Approximately 9:1 (probably less due to pistons being below deck height)

A few online calculators ask for teh HG bore. Without it infront of me I can only guess, but all in all, EVERY different calculator got approximately 9:1 Static CR.

Is there something im missing?

Edited by R32Abuser
bubba Grand Master

bubba

Posted
Posted

If deck height is below 0, wouldn't that increase compression??

I was more trying to make the point that the head and cams are fine.. there is no inherent problem with that type of head and cams that would cause this issue.

rob82 Mentor

rob82

Posted
Posted

Does the dyno plot look normal - like the cams are relatively in the right spot? If so that compression pressure is pretty much spot on.

My RB30/26 with CP 9:1 pistons was around 160psi +/-5psi - when I advanced the inlet 7degrees there was very little compression presure difference (maybe 5psi at most). This would suggest to me that your engine has the correct static compressure ratio of 9:1.

So many things to check before pulling the engine apart. Start by checking the CAS like I said.

R32Abuser Mentor

R32Abuser

Posted
  • Author
Posted

From all that I've read, and from thinking about it:

If the piston (flat section of the piston-not including domes/dish's) sits below the deck of the block, then the combustion volume when the piston is at TDC is larger compared to if the piston was sitting above the deck ("proud of the deck").

Correct me if Im wrong tho?

R32Abuser Mentor

R32Abuser

Posted
  • Author
Posted

Does the dyno plot look normal - like the cams are relatively in the right spot? If so that compression pressure is pretty much spot on.

My RB30/26 with CP 9:1 pistons was around 160psi +/-5psi - when I advanced the inlet 7degrees there was very little compression presure difference (maybe 5psi at most). This would suggest to me that your engine has the correct static compressure ratio of 9:1.

So many things to check before pulling the engine apart. Start by checking the CAS like I said.

Yup. Builder is slapping a different/known working CAS on it.

Taking it back to the dyno, checking if it knocks again, if so, getting a safe tune to do some k's on it. If not - great!!!

Thoughts?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Yup. Builder is slapping a different/known working CAS on it.

Taking it back to the dyno, checking if it knocks again, if so, getting a safe tune to do some k's on it. If not - great!!!

Thoughts?

Running in takes 20 -30 mins - get a proper tune and see what it can do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cleaning my wheels 😍

      By GTSBoy · Posted

      Yeah, my moulds and seals are 32 years old now. I think I will continue to not use a pressure washer on it.
    • Shoota_77
      Cleaning my wheels 😍

      By Shoota_77 · Posted

      I hear the old "I'd never use a pressure washer on my motorbike" BS in the dirtbike community too.  The only people that have had a problem from using a pressure washer on anything are the people that aren't using them properly.  If you hold the wand any more than 45 cms away from pretty much anything (radiators, wiring connectors, paint, etc) you aren't going to cause any damage.  We've had detailers wreck moulds and seals on cars at work before and the only reason why is they held the pressure washer too close and on the one spot for too long.  If you have 5% more brain power than a detailer then you know not to not do that and you'll never have a problem.
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      I'm pretty much healed up post surgery so I spent another almost full day out in the shed re-arranging everything to make room for all of the shit that I've taken off the car.  I need to get everything off the floor and away from the car for when I start making a massive mess stripping off the remaining body deadener and then for the the painting process.  Almost got the shed to a point now where I feel I can actually start working on the car again (clean shed clean mind or something!).  Almost 11 years of accumulated car parts, building supplies, tools, junk, etc have taken a long time to get in some sort of order again!  Most stuff is now boxed up and in the back shed if it's not car related.  Most people would still be horrified walking into my shed but it's significantly better than it was before!   For those that saw my separate post the other day, yeah I ordered one.... This version- I convinced myself to stop being a clown, wake up to yourself and realise it will take you 5 weeks to make one by which stage you're over working on the car again...  Maybe I am getting on top of my "mental ailments" and making smarter choices.... $1450 delivered which will take my miserable half-dutch arse a few days to get over having spent that much!  If I don't have a use for it straight away after my car is off it I might even see if there is a "rental market" for them.  See if anyone wants to hire it for a period of time.  $25 a week or something like that.  I'll worry about that when my car is actually ready to come off it though as that might be a while away!! There's now no excuses now for not ending up with an underside you could eat off! Away for kids sport the next few weekends so hopefully can get the rotisserie assembled ready to go for the car to go straight on it the next available weekend.    
    • The Bogan
      Cleaning my wheels 😍

      By The Bogan · Posted

      I always use my Karcher, but it's only a little one that I picked up from Supercheap  The only issue I ever had with a pressure washer was when I was a kid cleaning coaches, they had a hi-po industrial sized petrol jobbie that would strip paint if you got to close I saying this, we have a fairly high power washer at work with a diesel powered heater that sprays water at about 60°c, it works great for removing old wax and road grime on the underbody after some foam cannon action, albeit from a "stand off" distance of a few feet
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Sorry no - The sandtrap adventure ended the day, happened at the end of the last session. At that time I wasn't hearing any weird noises nor were the brakes shuddering anymore. It was only when watching the videos that I remembered I had these sounds early on!
×
×
  • Create New...