Jump to content
SAU Community

Recommended Posts

Hi guys,

I have searched a few times under a few different variations of heading and found nothing. All i need to do is remove my afm plug from the factory wiring and replace it with a newer better one. I was expecting the grey plasic plug to be half moulded and clipped together but it's a solid piece with a yellow insert. Am I right in assuming this Yellow insert is the key and if I remove that then the wiring will be able to come out freely? How do u do it without breaking it? The newer plug is second hand with a bit of wiring hanging out but would rather replace the lot rather than cut wires and solder then tape up.

Thanks in advance

Liam

Link to comment
https://www.sau.com.au/forums/topic/371345-changing-the-afm-plug-over/
Share on other sites

A pic might help, there are lots of different plugs around.

Usually you squeeze the two sides in and it should pop out, the yellow part is the inner part of the plug, it also has an outside grey part over it.

When i got mine it was twisted together and then taped up!!!

Hi guys,

I have searched a few times under a few different variations of heading and found nothing. All i need to do is remove my afm plug from the factory wiring and replace it with a newer better one. I was expecting the grey plasic plug to be half moulded and clipped together but it's a solid piece with a yellow insert. Am I right in assuming this Yellow insert is the key and if I remove that then the wiring will be able to come out freely? How do u do it without breaking it? The newer plug is second hand with a bit of wiring hanging out but would rather replace the lot rather than cut wires and solder then tape up.

Thanks in advance

Liam

You are going to have to make the electrical joins at some point; while it's possible to disassemble the plug and

connect the pins to the wires, you will probably get a better result from doing what you prefer not to

(i.e. join where the breaks are with solder and heatshrink).

Cheers,

SW

Geeze its not rocket science.....

Those plugs can easily be disassembeled , you just need a few precision srew drivers to get in there.....bear in mind however some of them can be very brittle and dont matter what you do, it will break, so you better hope your replacement is in good nick.

Yes the yellow piece is what locks everything in place ,remove that first....

Experiment on the one you have to replace

The whole reason I am asking was because I have never done it or even attempted it before and I don't want to break them. Precision screw drivers? Is the yellow piece clipped in? Screwed in? Just sitting there? Again just how does the yellow piece come out? Thanks for the info but I'm none the wiser as to disassembling it.

Use a flat and pry up in the middle of the front....the whole portion needs to be lifted as you would see three tabs holding the yellow piece from coming out

While you are prying the front get a next small flat and place it in the back of the yellow piece from behind and push it out....try to do it evenly and you will need someone to hold it steady for you

post-42272-0-33459800-1311111007_thumb.jpg

When you get out the yellow piece there are three individual tabs holding each wire terminal in place

Pry these down while holding the wire from behind and pulling it out at the same time .....these need to be moved a good bit for it to come loose.

post-42272-0-41733100-1311111041_thumb.jpg

Waallllaaaaa....

post-42272-0-87563900-1311111670_thumb.jpg

Now reverse the whole process and lets head for the bar

then just fit some new plugs

PC computers usually have good connectors to suit this type of application with locking tabs

check out places like jaycar etc online to find a pair of male/female clips with a locking tab

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...