Jump to content
SAU Community

Cant Get Oil Pressure

jarrod83

By jarrod83,
in Engines & Forced Induction

 Share

Recommended Posts

jarrod83 Community Regular

jarrod83

Posted
Posted

Hey Guys,

finishing my rb30 rebuild, it has a nitto oil pump, primed the system by filling up the outside hose of the oil cooler and cranking the engine backwards until it had sucked up a good 500ml of oil, left the hose off and cranked it over.

Absolutely none of the oil comes back out the hose almost like its draining straight through the pump, any ideas??

could the gasket that goes between the block and the oil pickup be leaking causing the oil to drain out of the oil pickup? or an airleak elsewhere on the pump causing the problem?

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/371949-cant-get-oil-pressure/
Share on other sites
r33_racer Grand Master

r33_racer

Posted
Posted

Did you put assembly lube or vasoline in the pump gears to help it generate more suction?

Why did you crank it backwards to suck in oil for? If you put some lube in the pump gears and pulled the plugs and injector lead and just wound it over it should prime normally.

Did you disassemble the pump by any chance and forget to do something up or left something out maybe?

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted

didnt put in any lube or vaseline, was just told to prime it by filling the pump out section with oil and crank it back a few times.

The only thing im a bit sketchy on is oil pickup gasket, i think i may have used the old rb25 one as i found what looks like the new one on the floor when i was cleaning up and i had already dropped the engine in. If theres no other possible causes i may have to "attempt" to drop the cross member and remove the sump and try replacing it. I was kind of hoping that i may of had two new ones floating around as ive used a fair few gasket kits.

r33_racer Grand Master

r33_racer

Posted
Posted

I know you cant drop the factory sump off with the cross member still there. If you dropped the cross member you could do it. Ive tried this before and couldnt get it off while the cross member was there.

Might be easier to just pull it all out and double check that gasket if its a big question mark. It would have to be a big leak for it to not prime up.

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted (edited)

so you couldnt get it to pump oil by priming it and cranking the engine?? You had to actually start it to get it going?

I completely removed the oil cooler and standard oil filter backing plate and left just an oil filter using the rb30 threaded fitting. Drained the oil out of it and pumped it all back in through the 1/8th bsb thread on the side of the block next to the oil filter.. cranked it over and still nothing.

I might pump the oil back through the fitting and check that its getting to the head and try starting it for 5 seconds.

Edited by jarrod83
JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

my old motor wouldnt make pressure cranking, even with a used oil pump full of oil and heaps of priming. even after 5 mins of cranking there was nothing, started it up and had pressure within 2 seconds. sometimes cranking just isnt enough, aslong as everything was assembled with lube and oil in all the right places it can run for a few seconds without pressure without doing any damage.

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted

fk, cant believe it, but i primed the f*kker, started it, oil pressure just flicked straight up...

besides opening the oil pump and filling it with vaseline i couldnt have done any more to prime it for pressure, cheers for all the input guys, wouldnt of attempted starting it without pressure without it.

Jarrod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...