Jump to content
SAU Community

Recommended Posts

Hello,

At this time I have a Magnaflow muffler on my car. I like the muffler, but I do a lot of long distance travelling and when you are in lower rev ranges (1500-3500RPM) the exhaust is very loud. Being distance travelling there is hills

where the RPM is in that cruise range and the minute you start going up hill/increasing the accelerator the car is very loud. I have tried getting over it, but it's so loud you can't hear the radio, you end up with your ears aching and sometimes

after a while you even get a headache.

I was wondering if there was any ways to quieten this around that rev range when it's straining more or is there a better muffler, performance and sound wise out there?.

1993 R33 GTS RB25DE

Thank you.

post-85033-0-18592400-1311513675_thumb.jpg

Edited by Brendonams
Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/
Share on other sites

Heyy i had the exact same problem with my muffler, i put a silencer on it but it didnt make much difference, so i went back to my stock muffler. You could try putting a silencer on yours but my advice is to change back to a stock muffler since you are losing power by using your current muffler. Your car is a non turbo (like mine) so the engine relies on the exhaust system to create back pressure, unlike turbo models which create backpressure from the turbo. By putting the muffler on you have robbed torque from your car. Im guessing you just chucked on a straight 3 inch mufffler or straight pipe on your standard exhaust system. Thats the same mistake i did, and i got a very loud exhaust which made it unbearable to drive. If you notice on the factory muffler, there is a butterfly valve thing, which actually connect to the throttle and is kept closed to give it more back pressure, this helps the initial torque to push the car in a higher rpm, the valve then opens to give the car more power as it climbs higher in the rpm to increase peak power. But by putting a different muffler the back pressure dissapears, causing the car to use more fuel and reduce initial accleration. The only place i can think of that sells factory mufflers is Dandy exhausts, thats were i got mine done, and it doesnt cost much. Mine costed 80 dollars to do. if you want power and a nice exhaust sound, you need to spend 1100 dollars on a proper exhaust system.

Edited by Deza3000
Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5930634
Share on other sites

btw in my opinion, just stick with the factory exhaust system, cause nissan engineered it for optimum performance, and the ecu is set to work with what the car currently runs on...e.g. the standard exhaust system. If you wanna change exhaust, then change to a cold air intake aswell, then do a ecu retune/remapp so it can run better. thats goona cost ya 2-3k if you want more performance, as for power gains your looking at 25-30kw. Which is actually a fair bit and i reckon you would be able to beat a ve commodore with that much power added on ;p

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5930637
Share on other sites

Ok, il have a look at getting a standard one, um I bought the car with the muffler on it. All i pretty much know is it has a Catback exhaust and the magnaflow muffler and it has a K&N Cold air intake.

How does the standard one sound and am I really going to get more power with a standard one? Ideas from others maybe as well?

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5930900
Share on other sites

hmmm you sure its a cat backk?? from my experiences catbacks arent as noisy, they have more of a nice tone, If it is a cat back then i dont think the stock muffler would bolt onto that. Take it to dande exhausts and tell them your problem, they will reduce the noise for you, do you live in melbourne??

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5931005
Share on other sites

Yeah, when I bought it the owner said it has a Catback exhaust on it, il take a photo of underneath the car tonight to see if you can tell. I live in Tasmania and i've taken it to a muffler specialist, he put another reasonator or something in it, he said there is no space for a second muffler and he said nothing else. The attachment is kind of like what I have on my car (Not exact)

post-85033-0-77259800-1311559876_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5931143
Share on other sites

Heyy i had the exact same problem with my muffler, i put a silencer on it but it didnt make much difference, so i went back to my stock muffler. You could try putting a silencer on yours but my advice is to change back to a stock muffler since you are losing power by using your current muffler. Your car is a non turbo (like mine) so the engine relies on the exhaust system to create back pressure, unlike turbo models which create backpressure from the turbo. By putting the muffler on you have robbed torque from your car. Im guessing you just chucked on a straight 3 inch mufffler or straight pipe on your standard exhaust system. Thats the same mistake i did, and i got a very loud exhaust which made it unbearable to drive. If you notice on the factory muffler, there is a butterfly valve thing, which actually connect to the throttle and is kept closed to give it more back pressure, this helps the initial torque to push the car in a higher rpm, the valve then opens to give the car more power as it climbs higher in the rpm to increase peak power. But by putting a different muffler the back pressure dissapears, causing the car to use more fuel and reduce initial accleration. The only place i can think of that sells factory mufflers is Dandy exhausts, thats were i got mine done, and it doesnt cost much. Mine costed 80 dollars to do. if you want power and a nice exhaust sound, you need to spend 1100 dollars on a proper exhaust system.

sorry bud just gonna correct you on this.

the factory muffler does not have a butterfly valve nor any sort of system that will do what you described.

what you've described is actually like what the HSV VE's "bi-modal" exhaust does, or similar to an x-force varex, which you can either control the valve manually with a remote & im pretty sure on the newer ones you can have it automatically adjust at certain RPM.

Yeah, when I bought it the owner said it has a Catback exhaust on it, il take a photo of underneath the car tonight to see if you can tell. I live in Tasmania and i've taken it to a muffler specialist, he put another reasonator or something in it, he said there is no space for a second muffler and he said nothing else. The attachment is kind of like what I have on my car (Not exact)

try somewhere else, there is definitely room for a centre muffler, the stock system has one so no reason why you cant have someone fit one to an aftermarket system.

i had the same issue, had a catback installed on my r34 with no centre muffler, it was horrible, i tried a couple of different exhaust shops over a weekend & the all said they can only fit a hotdog resi, so i ended up just booking it in with the guy who intially did it & he had no trouble fitting a small 8"x4" centre.

also, no chance of gaining 25-30kw from a cold air + exhaust on an N/A skyline haha

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5931185
Share on other sites

@ lindz34, The factory r33 skyline does come with a butterfly valve which is in one of the mufflers hole. The one in the skyline isnt electronic, It is actually connected to the throttle by the silver wire, similar to the one connected to the throttle body, and as the driver pushes the throttle, the valve opens to let out more air.

will upload a pic of my factory muffler

Edited by Deza3000
Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5931260
Share on other sites

sorry bud just gonna correct you on this.

the factory muffler does not have a butterfly valve nor any sort of system that will do what you described.

what you've described is actually like what the HSV VE's "bi-modal" exhaust does, or similar to an x-force varex, which you can either control the valve manually with a remote & im pretty sure on the newer ones you can have it automatically adjust at certain RPM.

try somewhere else, there is definitely room for a centre muffler, the stock system has one so no reason why you cant have someone fit one to an aftermarket system.

i had the same issue, had a catback installed on my r34 with no centre muffler, it was horrible, i tried a couple of different exhaust shops over a weekend & the all said they can only fit a hotdog resi, so i ended up just booking it in with the guy who intially did it & he had no trouble fitting a small 8"x4" centre.

also, no chance of gaining 25-30kw from a cold air + exhaust on an N/A skyline haha

"Some" R33 do have the butterfly valve on the exhaust, must have been a factory option - I got the official Nissan factory technical manual on the R33 and some cars do have this equiped.

R32 and R34 do not have this feature

For your exhaust just buy a high flow cat and put a stock rear muffler.

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5933164
Share on other sites

wow really?

that's cool haha

apologies for my failed attempt at correcting :P

anyway if it helps dude, i have a 2.5" cat back, small 8"x4" centre muffler & x-force varex rear oval muffler (cannons are quite a bit louder than oval shaped)

i drive on the freeway every day to & from work, sitting at 100kmph nearly the whole way & it's not an issue drone-wise, never been pulled up by the police for being too loud either.

there's a few options that the other guys have pointed out, so i guess it depends what you want, if you still want a nice sounding exhaust then go a centre muffler & if you want it to be more stock then obviously a stock rear muffler.

as for brands, my centre is a magnaflow - sounds nice.

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5933277
Share on other sites

  • 3 weeks later...

mine is a 2.5" with a hot dog AND a resonator AND recently changed to a mild steel oval muffler - every possible thing in the world to keep it quiet ...

its still very loud ... with the last exhaust change though it took a few weeks before the car started to keep it down so im hoping this is the same thing here and it will eventually shut up.

in terms of power - think more of 2-3 kw rather than 20-30

Link to comment
https://www.sau.com.au/forums/topic/371957-na-r33-muffler/#findComment-5961414
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...