Jump to content
SAU Community

Recommended Posts

I was told the boost would go up a few psi with new dump because theres less restriction at the turbo outlet, hence it spins faster n quicker, therefore more boost, so retune?? Have seen most threads where peopke just do the dump but no retune..

I was told the boost would go up a few psi with new dump because theres less restriction at the turbo outlet, hence it spins faster n quicker, therefore more boost, so retune?? Have seen most threads where peopke just do the dump but no retune..

Id consider an EBC to reduce the boost back to stock until you tune your car. Sudden spikes in psi might destroy your stock turbo.

I chucked on a hks split dump and 3 inch front pipe a couple off weeks ago and it changed my tune significantly. The car was happy to have a tiny bit more timing, was leaner in the first 5 load cells, was a lot richer in the midrange and leaned out up top. Needless to say I fixed it. I'm tuning my power fc with a wideband and datalogit btw. The boost level didn't change after the pipe swap.

Thanks for the reply so i guess a bigger dump WILL mess up with the afrs thus screwing up the tune, pretty annoying that u cant add things bit by bit without changing the tune, what about pple who change their full exhausts from stock i never hear of them havin a retune, exhaust is usually always the first of mods and most guys at this stage dont have an ecu to tune.. In my case i have the full exhaust n tuned ecu already, just need a 3" bellmouth dump that i dont have.

it would only alter the tune slightly, that is, use different cells

so depending on how your car is tuned, you might not need a "retune"

if its tuned properly, most tuners extrapolate the values to the neighbourhood cells on the map (ie the right way) so its fine if it varies a little

after all

air temp

air pressure

humidity

fuel quality

octane rating

these vary every minute of the date and you dont need to "retune" each second

so its prefectly fine and it might be ok, so don't "panic" but it is a good idea to check the AFRs on a dyno

but dont get sucked in if workshops "DEMAND" you must retune from scratch for a simple dump pipe

Just check it but like Paul said don't pay for a tune from scratch. It took me and the missus about 20 min of driving to fix mine.

No tuner would tune it from scratch anyway, they would just tidy up the existing tune, probably 30 minutes work max to confirm everything is in check.

If they say they are tuning it from scratch they are taking you for a ride as it makes no sense to wipe a tune and redo it, just a waste of time for no reason. They would most likely just touch it up and charge you more for the sake of it, I hope there are no tuners around that would do this though.

Edited by Rolls

That is why i dont take it to workshops, not only that, i know a fair bit of stuff myself so nobody can really take me for a ride, and still learning from all yous awesome peeps on sau...this website is great thanks to ya all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...