Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Cluster comes with 147Km on odo. Just goes to show how far wound back most cars are that are sold here (assuming fairly typical distance travelled). Having said that, I don't particularly want my car having an extra 50K added to the odometer. Then you got to explain to everyone who looks at it... lol

well your probably aware that 87-90 degrees of water is normal for our car.

its just how thin the radiator is and the load on it.

bigger radiator to take the load for winter will far out do the thermostat, especially if it ends up being too cold and keeps the car is a cold start map lol

Don't confuse the Nismo thermostat (which doesn't do that) with the Mishimoto thermostat (which does do that).

Bigger radiator would be more beneficial in the summer you'd think, yes?

Don't confuse the Nismo thermostat (which doesn't do that) with the Mishimoto thermostat (which does do that).

Bigger radiator would be more beneficial in the summer you'd think, yes?

yeh but there is a lower temp nismo thermostat available. isnt there?

i duno what your trying to get at

I thought Nismo was lower than stock, and Mishimoto was lower again.

Thought I read a thread on here where Scott fitted the Mishimoto and it was too cold and stuffed the car around, but I haven't seen much on the Nismo?

I run a 54mm race radiator and the Nismo thermostat.......no problems with my car with normal running in winter.....it hangs around 85 to 89 in traffic and about 84 on the freeway on hot or cold days....pretty sure from memory it was the same in summer.

On the track it dropped down 2 degrees and ran a perfect 83 degrees the whole time.......makes me think that it would do about 85-86 degree's in summer on the track!

Edited by Jetwreck

I run a 54mm race radiator and the Nismo thermostat.......no problems with my car with normal running in winter.....it hangs around 85 to 89 in traffic and about 84 on the freeway on hot or cold days....pretty sure from memory it was the same in summer.

On the track it dropped down 2 degrees and ran a perfect 83 degrees the whole time.......makes me think that it would do about 85-86 degree's in summer on the track!

Ahh too late sold it to Whiteaxis...LOL

yeh but there is a lower temp nismo thermostat available. isnt there?

i duno what your trying to get at

Below would be what I am getting at, thanks Ryan.

I thought Nismo was lower than stock, and Mishimoto was lower again.

Thought I read a thread on here where Scott fitted the Mishimoto and it was too cold and stuffed the car around, but I haven't seen much on the Nismo?

You don't really hear anything about them because the Nismo just works.

no you can legally change them over and report the change, to be honest i dont know whats involved. mine was only a few thousand off so i didnt bother

Mine has 25,000k's on the odo now. ;) I still have the original I can give the next buyer but I don't think they will care. Its obvious an aftermarket Nismo dash will change the K's isnt it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok will do, I think I originally had 1 bolt off for the sway bar on when I took off the strut but will give this a ago. Thanks Duncan! My sway bar has play also when I move it around, hoping that's the source of my squeaking because I can't find anything wrong elsewhere
    • odd. I thought all the top race teams used them.
    • undo the sway bar link, put it on last. put a jack under the outer ball joint on the lower control arm to raise the hub and off you go
    • I don't know how this is even possible. I removed the strut to do some work (it came out fine, and keeping in mind that I didn't put things back in the same order, but did this on purpose because I was supposed to remove the strut originally instead I tried to remove other shit first which made things a head ache) but now the problem is that it won't go back in. The alignment between where the bolt hole for the strut is and the j arm where the strut slides onto is way off, about a 10cm difference or more. In order to make it fit I'd somehow need to push it up. I tried to compress it with a spring compressor and install it but the compressor was getting in the way and there was no working room. On the photo you can see the difference between the shock and the thread that it's supposed to go on. The only things I removed in total were - the top bolts for the j arm but I didn't remove the actual j arm - the 3 bolts that hold the plate for the brake lines - the sway bar link (this bolted on back fine) - the strut/shock absorber
    • LOL that sounds pretty conclusive! Yeah if it doesn't work on a tight nut, it doesn't work.
×
×
  • Create New...