Jump to content
SAU Community

Recommended Posts

Hey Guys, selling the Power FC setup that was used with my big Z32 motor.

  • Replaces AFM with MAP sensors
  • Allows 20x20 mapping
  • Currently tuned for Nismo 740 injectors

All sensors, wiring harness and plugs are (included as pictured below) ready to fit.

ecua.jpg

plugsp.jpg

The hand controller can be used for tuning, and also displays the following

InjDuty - Injector Duty / How busy the injectors are

IgnTmng - Ignition Timing - Camshaft timing

AirFlow - Airflow meter voltage

PimVolt - Map Sensor voltage

Eng Rev - Engine revs

Speed - Road speed

Boost - Boost Pressure (requires optional boost kit fitted)

Knock - Knock sensor reading

WtrTemp - Water temperature or engine temperature

AirTemp - Air inlet temperature

BatVolt - Battery voltage

The hand controller also records maximum readings, so you can review max water temps/injector cycle/air inlet temps/knock numbers etc after a drive. I have found this feature particularly useful.

Also included in the sale is a Greddy multi switching unit. This was used to run the VTC on my VG30DETT, and the second output was used to run a thermofan. The Greddy is a two channel arming switch that can operate on anything from one to three paramters via the factory ECU or via external sensors. It can also function as an alarm/warning unit. This would suit someone wanting to run thermo fans, water/meth injection, nitrous, whatever...

greddy.jpg

Price: $1800 the lot, including freight, or best offer

Location: Sydney (North)

Condition: As New

sell power fc seperately? msg me on 0423 441 677

Hi, yes I would consider separating -hit me up with an offer.

????????

Just wrote back to your PM.

Considering the standard power FC's seem to go for around $1200 I'm not keen on letting the D-Jetro go for $1100... but thanks for the offer.

  • 2 weeks later...

A change of plans means asking price down to $1200 THE LOT. Sell the Greddy and make some money back...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • C34 Stagea RS4S Standard RB25DET Neo with ARP Headstuds and MLSR Gasket. Bosch 1000cc injectors Walbro 460 Standard neo inlet plenum w/rb25 s2 throttle body 6 Boost Low Mount Manifold Turbosmart Gen V 45mm wastegate (recirculated) Pulsar g30-770 (0.72 rear housing) 3.5"intake pipe to clear mounts, 3.5" dump to 3" exhaust Link G4X Ecu 380 hp on 98 octane, 478 HP on e85 (mainline hub dyno) Video of Earlier Run VID_300701109_043404_458.mp4 Final Dyno Sheet:    
    • Meh. Every single gear in my gearbox will crunch. I've been treating it nicely for >12 years now.
    • How fast are you doing the downshift? 4th gear was revised multiple times until 1998 to fix this issue. Synchro clips can fall out, synchros can wear. Most likely you're looking at a new transmission unfortunately. If you need to limp it until then double clutch downshifts into 4th.
    • Sorry I was being harsh there, but am I wrong? You can buy a M340i easily, and there's loads available second hand. A lot more workshops modifying them as well. How about getting parts for them? Don't get me wrong, I'd love a 400R, even a 4cyl (I looked at a few V36s before buying my shitbox BMW). Sadly Infiniti died in Aus and we're stuck with importing them as niche vehicles. Supply and demand
    • Probably straight swap for an R32 GT-R? lol
×
×
  • Create New...