Jump to content
SAU Community

Rb26 Itb's And Plenum On To Rb25 Or Rb20

darrinspencer
 Share

Recommended Posts

darrinspencer Grand Master

darrinspencer

Posted
Posted (edited)

I found this inlet manifold adaptor to fit Rb26 inlet plenum and ITB's on the Rb25's plus they do a Rb20 version

At first I thought they did the old cut and weld option onto a rb25 inlet runners, but it is different

Then I thought they had done a cut and weld onto a rb25 greddy style inlet manifold, but no

I think they have made up a new casting with mounting plates to bolt the ITB's onto and have made a remote seperate IAC box. It does away with the rb26 injector section of the inlet.

The attached pic's are are R34 Rb25det version.

Having a close look at the adpator it looks the same a greddy style manifold around the injectors ports and mounts. The flange onto the ITB's looks to be a 1 piece casting, ie not welded onto the runners.

Also the reason I think it is not a greddy style manifold is the angle of the radiator hose connection.

It is square like a factory manifold and not at a angle like the greddy.

The main negative problems with either the Blitz style adaptor plate is the angle of the injectors and the cut and shunt to stock manifold is the different runner spacing and angles.

With this version they seem to have solved those issues, I can not see any problems or disadvantage with this design

Cost is not cheap at approx $700-750 plus post form Japan etc.

Does not include the rb26 setup, so add $300-400.

Your thoughts??

I have Neo rb25det with greddy style manifold already, but would luv ITB's with VCT

post-14923-0-32770100-1312334463_thumb.jpg

post-14923-0-24473500-1312334473_thumb.jpg

post-14923-0-94677300-1312334480_thumb.jpg

Edited by darrinspencer
darrinspencer Grand Master

darrinspencer

Posted
  • Author
Posted (edited)

I found them on Yahoo. I think it will be close to $950-1000 landed

http://www.importmonster.com.au/view?url=http://page6.auctions.yahoo.co.jp/jp/auction/f101401033&thumb=http://f6.auctions.c.yimg.jp/img321.auctions.yahoo.co.jp/users/2/4/5/6/assemble2006-thumb-1297139207470101.jpg&title=RB25 NEO6 GTR KIT

As mentioned, they do a Rb20, R33 Rb25 and R34 Neo kit.

No mention on the company who makes them

They look similar quality to the other cheap chinese greddy styles manifolds.

They only cost approx $150 wholesale price in china for example.

Might try and find the supplier/manufacture as I have a few contacts and inport some parts from china now.

I currently run the greddy style copy on my Neo with gt3076r

I am very keen to try one of these out and do back to back test.

It won't be be for at least to 6-8 weeks thuo.

I can't really see any negatives with this setup?

Anyone have any idea's??

Edited by darrinspencer
darrinspencer Grand Master

darrinspencer

Posted
  • Author
Posted

i mean when you run the rb26 ITB's it apprently eliminates the vct.

I think that would happen when you use the full Rb26 intake with injector section and an adaptor plate as it would foul the VCT solnoid>

This kit is cast the same way, ie rad hose connection as the Rb25 manifold so it will clear the VCT. win win.

I have just email Aaron at IM to see if he can contact the seller and find out more info.

Johnny_B Enthusiast

Johnny_B

Posted
Posted

i found these on yahoo yesterday also after posting my comment.

although i could only find kits for rb20 and neo rb25

my rb25 is a s2 r33 engine.

definitely do more research into where the manifold is made, im eager to purchase asap

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana 路 Posted

      Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 馃槄
    • Dose Pipe Sutututu
      Question about BoV on RB25DET NEO

      By Dose Pipe Sutututu 路 Posted

      BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 馃珷    
    • Yeetus
      Question about BoV on RB25DET NEO

      By Yeetus 路 Posted

      I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • MBS206
      Question about BoV on RB25DET NEO

      By MBS206 路 Posted

      I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • GTSBoy
      Question about BoV on RB25DET NEO

      By GTSBoy 路 Posted

      But they do so for the other reasons to have a compressor bypass. It's in the name.
脳
脳
  • Create New...