Jump to content
SAU Community

Recommended Posts

  • Replies 183
  • Created
  • Last Reply

Top Posters In This Topic

What was it like to fit? Fitting instructions included?

bit of a PITA....I am sure after I do the next 2 things will be a lot easier..........destructions come with it.

Edited by Jetwreck

you don't even notice the shifts on light throttle

.........full throttle there is no clunking or harshness.....just super fast and precise!.....keeps the power rolling.

My gearbox would not change into 3rd at all unless you completely backed off and 2nd was flaring.....now it shifts without even thinking about it.

P.S. I have to admit at about half way I was a bit scared about the thought of drilling ect....didn't help that all the workshop guy's were laughing at me and saying they would not even attempt it.

Edited by Jetwreck

Do the changes on full heavy/full throttle too hard or chirp tyres on changes at all?

Sorry for all the Qs just chasing as much info and still trying to understand MV's decision on the kit.

no chirping and no destructive gear changes anywhere......I am putting out over 270AWKW's and I had no issue's.

I would agree.. the more I read the more frightened I became.. Solution.. stop reading. lol

Completely right. Only start reading when you've cracked it open & there's no returning. So, are you going to tackle this as a DIY?

I've started ringing around my local guys to see who sounds most confident & if they can do it for less than ~$250 - 300, this will be my first non DIY mod :O .

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

$500 for fitting including the fluid isn't that bad I wouldn't think? And I've had no issues with the Valvoline trans fluid, just make sure they're using the Maxlife version, as that is the Matic J compatible one.

Anyone got a link for the fitting instructions? There are videos on the web site but I can't find the exact fitting instructions. If it's not too bad I'll just get dad to do it.

I take it this is where the price difference comes in for Craig's changeover VB. Worth it if it's going to be a hassle!

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

$500 for installation and Oil is a good price imo......but no more than that!spank.gif.......it's about 4 hours work with the correct tools.....but 1 stuff up and your screwed!

try this when pricing......tell them it's a 350Z auto...that they will understand...it's the exact same shit.

http://g35driver.com/forums/engine-drivetrain-forced-induction-diy/313499-diy-transgo-valve-body-upgrade.html?ref=esp-link

have fun!!! :P

Edited by Jetwreck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • One other thing worth mentioning when I did this job I only jacked up the driver side as I was only doing work there, but from what I understand both wheels should be in the air when removing the sway bar links?
    • Yep it's an r34. Usually people remove struts without removing the front upper control arm (fuca is what i assume this is?) So not sure why mine wouldn't fit. I know on my other car I did a similar job and it wouldn't fit until I removes the ball joint nut even though I didn't remove it prior.   The upper arm doesn't seem to be in the way (the part that's bolted to the chassis. The part that's bolted onto the j arm I'll check that out though.   I was going to compress the spring and put it in with the compressor attached but not sure if it will work  Haven't seen anyone do it.
    • I have a small lip on the boot of the E90 and I've been toying with the idea of trying to mould it in to the boot to remove the gaps. I guess shaving the seams? No idea what the terminology is here.  What I'm wondering is, if it's current double sided taped down, what would I do to more permanently attach it so it makes a good base for the filler? It only has edges so no way to bolt it down unless I add some braces. I've done a lot of fibre glassing in my time so that's nice and easy but I'm not sure what my options are here.  Sorry, this is the best pic I have and I'm 4 million ks from home ATM.  
    • Based on this comment I went googling. A052's in the sizes I want are certainly not cheap, but I couldn't find anything in the V70A anywhere. How much do they run/where do they get sourced from? From what I know (nothing but internet searches and reviews etc) the R888 has pretty much fallen off from anyone's actual use, and the AO52 is the king of "road legal" rubber. Nobody is driving around on their daily for Z221, AO050, DZ03G. At that point, for purely track only tyres - Why not buy actual slicks? Why does nobody actually do that anyway?
    • This an R34? It shouldn't matter though - it should be the same as on any of the others, and by "any of the others" I mean R32, because that is the car that I have had the front end apart on about 50 times this year. Sometimes, it is much easier to get the lower shock eye onto that pin when: a) you have the upper shock nuts backed off a few turns so you can wiggle it a bit more freely. When they are tight the bottom of the strut is much harder to move that _leeeetle_ bit you might need it to to win the fight. b) you have the outer bolt(s) from the FUCA out and so you can move the lower pin around freely too. Then, all you have to do is put the upper arm back on when you've got the rest back together, and this is where jacking under the balljoint can help.
×
×
  • Create New...