Jump to content
SAU Community

Recommended Posts

  • Replies 183
  • Created
  • Last Reply

Top Posters In This Topic

What was it like to fit? Fitting instructions included?

bit of a PITA....I am sure after I do the next 2 things will be a lot easier..........destructions come with it.

Edited by Jetwreck

you don't even notice the shifts on light throttle

.........full throttle there is no clunking or harshness.....just super fast and precise!.....keeps the power rolling.

My gearbox would not change into 3rd at all unless you completely backed off and 2nd was flaring.....now it shifts without even thinking about it.

P.S. I have to admit at about half way I was a bit scared about the thought of drilling ect....didn't help that all the workshop guy's were laughing at me and saying they would not even attempt it.

Edited by Jetwreck

Do the changes on full heavy/full throttle too hard or chirp tyres on changes at all?

Sorry for all the Qs just chasing as much info and still trying to understand MV's decision on the kit.

no chirping and no destructive gear changes anywhere......I am putting out over 270AWKW's and I had no issue's.

I would agree.. the more I read the more frightened I became.. Solution.. stop reading. lol

Completely right. Only start reading when you've cracked it open & there's no returning. So, are you going to tackle this as a DIY?

I've started ringing around my local guys to see who sounds most confident & if they can do it for less than ~$250 - 300, this will be my first non DIY mod :O .

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

$500 for fitting including the fluid isn't that bad I wouldn't think? And I've had no issues with the Valvoline trans fluid, just make sure they're using the Maxlife version, as that is the Matic J compatible one.

Anyone got a link for the fitting instructions? There are videos on the web site but I can't find the exact fitting instructions. If it's not too bad I'll just get dad to do it.

I take it this is where the price difference comes in for Craig's changeover VB. Worth it if it's going to be a hassle!

Well, I heard back from a shop that does a lot of Transgo work. His sugestion was for me to buy the kit online (derr, was going to anyway) because he can't buy it that cheap thru his supplier.

Then his price for installation was somewhere between $500 & $1000 (unsure as to the extent of the work) but that included filling it up with their Valvoline trans fluid. I DON'T THINK SO. :spank:

Looks like I keep asking or another DIY project is on the cards.

$500 for installation and Oil is a good price imo......but no more than that!spank.gif.......it's about 4 hours work with the correct tools.....but 1 stuff up and your screwed!

try this when pricing......tell them it's a 350Z auto...that they will understand...it's the exact same shit.

http://g35driver.com/forums/engine-drivetrain-forced-induction-diy/313499-diy-transgo-valve-body-upgrade.html?ref=esp-link

have fun!!! :P

Edited by Jetwreck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok will do, I think I originally had 1 bolt off for the sway bar on when I took off the strut but will give this a ago. Thanks Duncan! My sway bar has play also when I move it around, hoping that's the source of my squeaking because I can't find anything wrong elsewhere
    • odd. I thought all the top race teams used them.
    • undo the sway bar link, put it on last. put a jack under the outer ball joint on the lower control arm to raise the hub and off you go
    • I don't know how this is even possible. I removed the strut to do some work (it came out fine, and keeping in mind that I didn't put things back in the same order, but did this on purpose because I was supposed to remove the strut originally instead I tried to remove other shit first which made things a head ache) but now the problem is that it won't go back in. The alignment between where the bolt hole for the strut is and the j arm where the strut slides onto is way off, about a 10cm difference or more. In order to make it fit I'd somehow need to push it up. I tried to compress it with a spring compressor and install it but the compressor was getting in the way and there was no working room. On the photo you can see the difference between the shock and the thread that it's supposed to go on. The only things I removed in total were - the top bolts for the j arm but I didn't remove the actual j arm - the 3 bolts that hold the plate for the brake lines - the sway bar link (this bolted on back fine) - the strut/shock absorber
    • LOL that sounds pretty conclusive! Yeah if it doesn't work on a tight nut, it doesn't work.
×
×
  • Create New...