Jump to content
SAU Community

Recommended Posts

I have decided to sell my 1999 R34 GTR VSPEC. I thought I would put it up here so a true Skyline enthusiast would have first bite of the cherry so to speak. My elderly folks have asked me to help them out financially so this is the right thing to do.

I am asking 39k firm for the car, so its probably the cheapest GTR VSPEC in the state. And its an absolute monster! (the car has been tuned and dyno'd at 380kw at all wheels, but currently sits at 334kw at all wheels with a recent dyno done at ENVY dyno). It has appeared in High Performance Imports magazine amongst others and has been on various DVDs.

The price is for 2 reasons.

Firstly, The car has a new engine. The new engine has done 32000 kms and was build buy ENVY Performance at Brookvale. In fact every bit of work including importing the car has been done by ENVY. I have all the relative paperwork from the original import papers to the major work receipts. The extensive work has cost around $45k. Secondly the odometer reads 162000 km. These two facts would probably turn the average buyer away. However this car is in great condition (see the photos) I am going to advertise my car here for a few weeks and through ENVY only as I want someone who really appreciates all the work that ENVY has done on this car, and the value of the modifications. I would like to avoid tire kickers and people who want to drive my car or offer me silly money. The price is already good I rekon.

The components are listed below:

Full ENVY Built 400kw engine

New Block, New forged pistons and new forged rods

New dash 5 Turbos, dump pipe

New ENVY Cams and cam gears

Ported ENVY Head complete with new valves, valve springs

Adjustable Vartex Xforce exhaust (electronic controlled dampener )

500cc Hi flow Nismo injectors

New coil packs

Apexi computer

Power FC with controller

Digital variable boost controller with 3 adjustable settings

GReddy oil pump

New water pump

Remote oil cooler

4inch Front Mount intercooler

Exceedy Heavy Duty clutch

Sump baffle kit

Bosch in tank Fuel Pump

Quicktrack alarm system and Cobra 3point immobilizer

NISMO White 320klm Instrument Cluster

Xenon headlights

Bluetooth connectivity kit

Ipod/mp3 connectivity kit

carbon fibre mirrors (originals available as well)

VSpec options: - Carbon fibre rear underbody tray

- Intercooler intake temp sensor

- Exhaust temp sensor

- Upgraded MFD to show data for these two extra sensors

- Slightly different tacho (smaller increments)

- Active rear diff

- Faster ATTESSA computer ( Advanced Total Traction Engineering System for All-Terrain)

Here are the photos:

post-83702-0-27818200-1313218683_thumb.jpg

post-83702-0-40914500-1313218698_thumb.jpg

post-83702-0-74436100-1313218719_thumb.jpg

post-83702-0-89552300-1313218738_thumb.jpg

post-83702-0-55729700-1313218759_thumb.jpg

If you would are a serious buyer and would like to see the car I would be happy to show you. I also have many more photos. Call me on 0404484731 or contact me at [email protected] or pm me here.

Thanks everyone,

Layne

Edited by Bigvis.
Link to comment
https://www.sau.com.au/forums/topic/373888-for-sale-1999-r34-gtr-vspec-39k/
Share on other sites

envy is in brookdale nsw so i am assuiming somewhere close to there. i love how just about all envy skylines i have seen have the yellow blue engine covers, was that personal choice lol free bump for an awsome car and it won't last long at the price

Hi everyone,

The car is on the Northern Beaches yep. I did get a blocked call iwantagtr so try again if you want to know more as I did get youre missed call but could not return it.

The car is very cheap as I'm sure everybody here realises and I have had a lot of interest but it is not sold yet. I have had a couple of offers for a trade so thankyou to those people as well. If I change my mind on a swap I will let everyone know.

As far as the injectors go..I dont drive it hard. I dont think I have ever had them work above 22% or their capacity according to the dash computer. They arer what ENVY installed for this engine. Bear in mind that it is currently tuned to 334kw at the wheels at 18psi for daily driving/street car. There is much more it can give Im sure, but with the power it has and speeds it can do I would never need more lol.

Fell free to contact me and thanks for the interest and nice comments so far. I really hope I can sell it to someone from these pages.

Layne

Did this have ACCESS plates on it before?

Don't know what envy do with injectors but when i was there they told me my stock RB25 injectors would be good for 300KW ATW.... maybe they crank up the fuel pressure??

can someone explain the front bars on 34r's please

some have a smaller front lip (black)

and some have the larger one

and v specs have nothing... im the market for a 34 gtr, but do want the larger of the 2 front lips

Standard gtrs have no 'diffuser' like in the pics of this one as its been removed. V-specs do have the front diffuser and rear carbon fibre diffuser from factory. You'll notice this one still has the rear one fitted. People often remove the front diffusers like this one as they sit quite low even at factory suspension height so would be even worse when lowered and wouldn't take long to damage

actually good question...wheres the vspec front lip, side skirts and pods

They don't come with Side Skirts and pods from factory albeit lot of people fit them after wards

as for the front lip as like mine is near impossible to keep in one piece in Australia roads.. bloody thing scrapes everywhere with low ride height. so got it removed

good thing is unlike the back diffuser the front one is very cheap to replace and is made from plastic composite and not Expensive Carbon fiber like the rear

have to say good price for Bay side Blue V-Spec as 39K is normally Silver R34 GTR price's, not to mansion the build engine

They don't come with Side Skirts and pods from factory albeit lot of people fit them after wards

as for the front lip as like mine is near impossible to keep in one piece in Australia roads.. bloody thing scrapes everywhere with low ride height. so got it removed

good thing is unlike the back diffuser the front one is very cheap to replace and is made from plastic composite and not Expensive Carbon fiber like the rear

have to say good price for Bay side Blue V-Spec as 39K is normally Silver R34 GTR price's, not to mansion the build engine

cheers for updating me on that lads....

Im sure this will sell quick, I think info on these injectors would be important to find out for any buyer but.

Called up Envy today. Car is running 500CC injectors. Was told they're pretty much maxed out at close to 100% cycle duty and will need to be upgraded if chasing any more power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...