Jump to content
SAU Community

Recommended Posts

Turbo and intercooler bypass (D-valve)

A method by which a large zero cracking pressure one-way check valve is inserted just prior to the throttle body, enabling air to bypass the turbo, intercooler, and piping during periods where there is negative air pressure at the throttle body inlet. This results in more air combusting, which means more air driving the turbine side of the turbo. As soon as positive pressure is reached in the intercooler hosing, the valve closes.

Sometimes referred to as the Dan Culkin valve.

When used in a MAF configuration, the D-valve should draw air through the MAF to maintain proper A/F ratios. This is not necessary in a speed-density configuration.

thats pretty cool, very passive system, wonder how well it would work.

Evos have factory antilag, but having it on anything else would be impossible to get engineered short of a drive cycle test, in which case it wouldnt effect the reading(depnding how it was setup)

...Strange eh.

tmk they have the air bypass hardware but not the required ECU mapping.

I can't imagine any manufacturer that offers warranty leaving this "feature" enabled.

Cheers,

SW

I setup antilag on the Vipec for shits and giggles (it's not 100% setup as I'm not that keen on it). Definetely not good for your car though.

You sure Evos have it from factory? What models? I've never heard that before that's all.

You mean proper antilag for between gear changes or just launch control antilag? (I wrote up a post in the past explaining all the different things people refer antilag to but can't be bothered finding it).

How did you set it up exactly? I heard they install a fuel injector or something into the exhaust mani?

Have you also setup the launch control or flat shift?

How did you set it up exactly? I heard they install a fuel injector or something into the exhaust mani?

Nah you don't install an extra injector. It just retards the timing by a huge amount and opens the injectors to create a lot of unburnt fuel so it can ignite in the exhaust manifold. It's all just settings in the ECU.

Have you also setup the launch control or flat shift?

Nah havn't done that yet. Launch control is something I want to setup in the future though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, I’m currently running a str pipe hi low hks exhaust and downpipe. Was wondering if I change out muffler to a titanium one will it change the sound of the exhaust? Plus I have always liked the look of the titanium pipes … anyone have recommendations to one?    side note already have titanium intake pipes. 
    • I looked up my other car that is a R33 GTST series 1.5. Anyone able to confirm what a Aero Form Bumper is?     (1G) 2 Door Coupe; (2GK + 11V) RB25DET; (4B) 2WD HICAS; (7F) 5 Speed Manual; (14G) Super Fine Hard Coat; (15U) Large Rear Spoiler + Aero Form Bumper + Rear Wiper (Aero Selection)
    • Ha ha, all good! I've almost caved in and realised I'm buying one.  I know myself well enough by now that I will start chasing ADHD butterflies half way through building it and not finish it so I'm better off spending the extra money buying one instead of making one just so I can get into straight away.  I would very much enjoy making one as fabrication is probably a strength and definitely a passion but I don't want that to be at the detriment to the car I'm ultimately building it for! There's some pretty good ones around for ~$1100 at the moment so I think I'll just go that way.  At the end I sell it or as mentioned, get another project to make further use of it! Thanks gents.  
    • That link was very helpful thank you.
    • That is the option code, not the VIN. Regardless all of that production is considered series 2: https://gtr-registry.com/en-ecr33-vin-table.php
×
×
  • Create New...