Jump to content
SAU Community

Accessport Fast Flash

Snowman

By Snowman,
in R35 GTR

 Share

Recommended Posts

Snowman Grand Master

Snowman

Posted
Posted

Hey all,

Started playing with the R35 yesterday and one of the things I was really looking forwards to seeing was the "Fast Flash" feature that now exists with the Accessport.

But despite updating to the latest Firmware the flash was still taking 10-15mins - which is a killer for proper dyno tuning.

All maps are V3.00 maps.

Anyone else have this issue?

Link to comment
Share on other sites
LSX-438 Mentor

LSX-438

Posted
Posted

The first time i got a new map it took 10 mins or so, thereafter maps flashed in very quickly. So perhaps it is the AP setting up the 'environment' the first time you do it. Or perhaps the maps need to be prepared for fast flashing?

Link to comment
Share on other sites
Snowman Grand Master

Snowman

Posted
  • Author
Posted

Well I was flashing in-between the tune that was in the car already (the car is a JDM 2008 - been here a while now and had the Cobb for a while too).

There was the "mail order" tune in it which we then swapped to the Cobb basic Stage 2 tune - then back to the mail order tune that was in it - then back to the Cobb tune but this time used the Cobb tuning software rather than just the hand controller - and they all took 10-15mins.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • alexburns
      Interior Light Problems

      By alexburns · Posted

      @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Duncan
      GReddy Injector Help!

      By Duncan · Posted

      Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...