Jump to content
SAU Community

Recommended Posts

hi guys currently getting my motor built at moment it will be ready to get tunes soon when its back in and i was wondering cause im new to wa where is the best place to get it tuned a reputable place ?

its a r32 gtr by the way

please pm me

thanks guys

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

hi there, best place in town is allstars in malaga, they do a good tune and get plenty of good feed back. im getn my r33 gts done there in the next few weeks.

Big question is who built the engine ? Whenever tuning a new engine there is alot of reluctance, cause when something goes wrong, as is often the case, the tuner doesn't want to get blamed for a poorly built engine, and vice versa.

Also, what ECU have you got, turbs etc ?

Please post results in the SAUWA Member area :thumbsup:

If the bad boy works, I'll be telling every one don't u worry,

Quick parts list

Bottom end built by me with

Nissan bearing

Spool rods

CP pistons 86.5

Nitto pump

Trust sump extension

Head consists of

Tomie -

Pro cams 270x10.8

Type B springs and retainer

Bronze valve

Ferrea +1mm valves

Tomie gaskets

1.2 HG

1000cc xpurts

GT 35 .82 vband

3.5" dump

6 boost and 48mm pro gate with screamer

040 intake and 2x 044 externals all direct wired

3lt surge tank

3lt baffled catch can with rear head drain,

Think I covered everything and all issues RB related

Let's hope it all works

  • 2 weeks later...
  • 5 weeks later...

MOTOR BUILD UPDATE, ALL BUILT AND FINISHED GOING BACK IN CAR NOW !!! maybee some things i missed out !!

sard 700 cc injectors

brand new garret 2860-5 turbos with all new gaskets

hks exhaust gasket and tomei metal intake gaskets/throttle bodies

acl race series full engine bearing kit, along with king bearings unknown what they were for !

shim head gaskit race series (metal)

N1 water pump

tomei UMEDA oil pump

tomei 260 deg cams

custom built extended sump and pickup with trap door setup in sump (MADE BY RED R RACING )

rebuilt front diff and preload reset

engine balance

machine crankshaft

ross harmonic balencer

cp forged pistons, 30thou over size from original bore

eagle conrods

gates performace timing kit

replace crankshaft oil galleries with screw in plugs

deck block

recon head ,full set of valve guides,3 angle valve cut ,set of shim tappets to cams supplied

aftermarket valve springs

custom work (drill and weld up oil galleries in head advised by red r racing)

TOMIE Oil Feed Restrictors

TOMIE Sump Baffles

HKS Adjustable Cam Gears

ARP Mains + Head Studs

All New Hoses And Gaskets

Oil Relocation Kit + Cooler

alloy Radiator

new clutch built by (JIM BERRY RACE CLUTCHES QLD)

Nismo Airflow Meters

New O2 Sensors

trust 600x300x120mm Intercooler,

recent full rebuild on gearbox

running the nistune ecu with nismo afms

and a blitz i colour elect boost controller

will be interesting to see how much power i will make ,would anyone know an estimate on power figure ?

Thanks I bought these brand new turbs cause I blew one up originally when I had same turbs before not expecting motor to go and make a new stronger motor with more power so yeah I hope I can make some good power anyways was hoping for 600 but oh well ...

Thanks I bought these brand new turbs cause I blew one up originally when I had same turbs before not expecting motor to go and make a new stronger motor with more power so yeah I hope I can make some good power anyways was hoping for 600 but oh well ...

A mate with an RB28 running 26psi and e85 with big cams and a shit load of head work made 630rwhp, so with your setup on pump98, and similar boost I'd expect around 550rwhp thumbsup.gif

but thats really a guess whistling.gif

Make 500 easy, pending ignition and boost will indicate how far you want to go. Camshafts could be alittle bigger for some extra hp, I changed from 260's to 272's and noticed a mega difference top end. Either way, great street and all round setup.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, that is a helpful description, because that sounds exactly like a bleeding issue in the clutch....these are hard to bleed manually even when the damping loop has been removed. I'd suggest bleeding again....start by filling the master cylinder up and opening the bleed nipple. Come back and check every now and then that the master cylinder is not empty. Let it gravity bleed for a few hours and see if that improves
    • I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
×
×
  • Create New...