Jump to content
SAU Community

R33 Gtr Boost Gauge Installation

AzN

By AzN,
in Engines & Forced Induction

 Share

Recommended Posts

AzN Collaborator

AzN

Posted
Posted

I installed a boost gauge on my R33 GTR but couldn't find any grommet holes in the firewall to run the vacuum hose through

so I did a quick job by putting it through the side fender and now the gauge is not working because the hose is squashed.

Can anyone tell me where to run the hose through the drivers side? The gauge is mounted onto the right air vent and the hose is squashed due to me trying to hide it under the trimming.

Link to comment
https://www.sau.com.au/forums/topic/374551-r33-gtr-boost-gauge-installation/
Share on other sites
erik Community Regular

erik

Posted
Posted

i ran a couple lines and wires for boost gauge and controller yesterday, the grommet isn't in the engine bay.

it is a hole in the engine bay at the very back on the drivers side, pretty big hole with wires already going through it,

the grommet is in your wheel arch under the plastic guard that stops shit flicking up from your rear wheel.

luckily (unfortunately) for me my gaurd must of been loose and rubbing on the wheel and has worn away so it was easy for me to get to just by lifting it up.

you'll need to undo the gaurd and stab a hole through the grommet with a screw driver and push the hose through then the other end goes into the engine bay through that hole with all the wires

if you still need help i'll pm my number give me a call and i'll send some photos

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' R34 GTT Series 2

      By hoodedreeper · Posted

      Sorry for resurrecting an oldish thread Not much has happened in the past year since the last update. The car did another 1000 miles or so and failed the MOT for the first time in October (failed on tyres which had been advised for a couple of years) In October the car got put up for sale and was removed in November due to no interest, being so close to christmas it was to be expected. The roads were dry in February so I decided to tax it early and get the new tyres fitted.   Fast forward to April, I got someone in to give the car a good clean after sitting for the winter.                                 The car got re-advertised and today (Saturday 3rd May) the car sold. The new owner is planning a GTR conversion at some point and a respray in the same pearl white. It's bitter sweet, it's a shame to have the car sit there for half the year and then only do 1000 miles. The kids are growing too quick and space in the back is getting limited. It's been a great 6.5 years of ownership
    • MBS206
      Rb26/30 build

      By MBS206 · Posted

      And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Butters
      Rb26/30 build

      By Butters · Posted

      Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • GTSBoy
      Rb26/30 build

      By GTSBoy · Posted

      2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
×
×
  • Create New...