Jump to content
SAU Community

Recommended Posts

hey guys i am looking for a z32 afm now i am just wondering  do i get a tt awf or a n/a afm

oh and i have a r32 gtst if that makes a dif

I don't know what awf is, but N/A and TT Z32 AFMs are identical - p/n 22680-30P00, red sticker

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5976548
Share on other sites

ahh ok and ill get the part number and check it that way

it isnt brand new its 2nd hand

Why risk it with a 2nd hand AFM? It simply is a waste of money.

But a new one, from a respected workshop - you won't get a fake, or one that could break in 6 months.

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5977421
Share on other sites

Might want to read this first under the z32 wright up about z32 afm:

http://www.garage7.com.au/

They look the same until you cut them open.

i had a look at this site good info there use have convinced me to get one of these lol

now the mission to put it on

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5977592
Share on other sites

Don't know what all the fret is over second hand genuine units are... Most of these are run with good filters. What if someone bought a brand new unit for their car, used it for 6 months, and then upgrades to map and sells the afm for half the price? Its a good saving on a unit which hasn't much age and will probably last you the life of the car...

I bought my genuine piece over from the US a while back. Never had any issues with it(touch wood). I wouldn't buy an "z32 alternative". Often, the fake ones are listed as alternatives or aftermarket parts.

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5977625
Share on other sites

How do you know someone only used it for 6 months?

You don't.

AFM's are so cheap that it's just not worth the risk. They seem to only last 10yrs anyway so almost a consumable like a timing belt really. They certainly don't last the life of the car at all. AFM's are known to fail regularly.

A 2nd hand Z32 could be 5 years old for all you know, and belted around a bit. For the sake of a couple $$, just get a new one.

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5977753
Share on other sites

Exactly anyone can say part x has done 10000km, but in reality it has probally done close to 100000km. That's the problem with buying second hand parts. Seeing as the afm is a critical part of keeping everything running sweet i don't see why people don't fork out the extra say $100 for a new one. I got my bosch one bran new for $310 from bursons.

Link to comment
https://www.sau.com.au/forums/topic/374647-z32-afm/#findComment-5977838
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is lower price now given apparently nobody wants these or needs them. It's 550 but if someone sees it on SAU and wants to make an offer, please do so.
    • LS is a good motor, but it hurts my soul when I see it in a RB. Guess it fixes the oiling issues lol.
    • I'm confused. Does this qualify as "Gregging" or are you somehow avoiding the Gregging?
    • More assembly going on, with all sorts of "bolt right on bro" scenarios going on here. Smartly, PTV clearance was checked. And I say smartly because it turns out that the intake was 0.009" from piston meeting valve. This is 0.23mm. This is very not okay. A fast meeting was facilitated between engine builder in Australia and engine builder in the USA which was actually incredibly helpful and constructive actually, various ideas thrown around to get around this issue including: 1) Retard the cam timing which would have brought the exhaust valve closer to meeting piston (it was 0.065") which was uncomfortably close to begin with, and change the cam profile making it 'laggier' 2) Much larger head gaskets which would reduce compression, but half the point of this was to increase compression. 3) New set of pistons ($$$$$$$$$$$$$$$$$) 4) All of the above 5) Get ghetto The concept is you get sticky sandpaper and stick it back to a valve, slightly larger than the valve you/I'm using, like say from a LS3/rectangle port head. You now have a very super advanced flycutting tool to modify your pistons in your block. Then you install it in your head, and attach the other end of the head to a drill. Then you just replicate your valve smashing into a piston with your spinning drill.   This is the result. Repeat many times. It is strongly recommended you have some kind of fixed stop when doing this for extremely obvious reasons because if you press too hard then you're well into apocalyptic repercussion land. The minimum clearance on the intake valve is now 0.075" this is still in the "Too close to be really comfortable" and into "It should be fine" land. Supposedly in the real world the clearances will be slightly bigger. Guess this is what happens when people push envelopes for N/A engines instead of adding boost! Time to move onto the new, upgraded, higher ratio roller rockers from Yellaterra, all tapped and threaded with a stronger bolt for better stability. Very nice. Lets see how they fit. For f**ks sake. Time to bring the grinder out for these aftermarket, machined and CNC'd heads. Looks like the new, beefier rocker from YellaTerra has gone from Bolt on part to "Bolt on part". Well, lets see how this bolt on crank scraper and windage tray goes then, shall we? There actually is more clearance than they specify for this thing, but seeing it all move as you check it is terrifying when you see it all so very very very very nearly hit things. But after all, this is what the item is designed to do after all and actually did bolt on perfectly and have enough clearance to everything and some very clear and direct instructions. So +1 to Improved Racing I suppose. As above with the windage tray on. Photo of breaker bar wonkiness for added lols. Next up: Oil pump/front cover/water pump/sump and then it's time to actually install the heads, pushrods, head bolts, valve cover gaskets and such is all there and ready to go. (except the oil pump bolts which were previously longer for more clearance with the previously perfectly installed double row timing chain). There's definitely a sense that someone other than us has been here before and done everything perfectly, or at least considered it and came up with working solutions. Perhaps the previous cam was 6deg advanced to avoid PTV issues with the milled stock heads? In any case when I attempt to sell this stuff the buyers are going to be very directly informed.
    • my catch can is pretty easy to empty but it overflows due to the blowby/crank case pressure etc. max I have drained is ~600ml even with a ~2.3L capacity. So it is not just about having to drain it out its the mess it makes down the firewall and under the car and rear passenger tyre from the overflow oil being blasted by screamer + air in general. Ending up on the ground cleaning the oil up and having oil on your arms when everyone else can chill and watch the other sessions gets old fast
×
×
  • Create New...